- semantics and behavior of local atomic operations.
lockdep-design.txt
- documentation on the runtime locking correctness validator.
+lockup-watchdogs.txt
+ - info on soft and hard lockup detectors (aka nmi_watchdog).
logo.gif
- full colour GIF image of Linux logo (penguin - Tux).
logo.txt
- directory with information on the NetLabel subsystem.
networking/
- directory with info on various aspects of networking with Linux.
-nmi_watchdog.txt
- - info on NMI watchdog for SMP systems.
nommu-mmap.txt
- documentation about no-mmu memory mapping support.
numastat.txt
shared across all System Controller members.
TC/TCLIB Timer required properties:
-- compatible: Should be "atmel,<chip>-pit".
+- compatible: Should be "atmel,<chip>-tcb".
<chip> can be "at91rm9200" or "at91sam9x5"
- reg: Should contain registers location and length
- interrupts: Should contain all interrupts for the TC block
With some exceptions, these support nvidia,high-speed-mode,
nvidia,schmitt, nvidia,low-power-mode, nvidia,pull-down-strength,
- nvidia,pull-up-strength, nvidia,slew_rate-rising, nvidia,slew_rate-falling.
+ nvidia,pull-up-strength, nvidia,slew-rate-rising, nvidia,slew-rate-falling.
drive_ao1, drive_ao2, drive_at1, drive_at2, drive_cdev1, drive_cdev2,
drive_csus, drive_dap1, drive_dap2, drive_dap3, drive_dap4, drive_dbg,
drive groups:
These all support nvidia,pull-down-strength, nvidia,pull-up-strength,
- nvidia,slew_rate-rising, nvidia,slew_rate-falling. Most but not all
+ nvidia,slew-rate-rising, nvidia,slew-rate-falling. Most but not all
support nvidia,high-speed-mode, nvidia,schmitt, nvidia,low-power-mode.
ao1, ao2, at1, at2, at3, at4, at5, cdev1, cdev2, cec, crt, csus, dap1,
High level behavior (mixed):
============================
- kernel(driver): calls request_firmware(&fw_entry, $FIRMWARE, device)
-
- userspace:
+ 1), kernel(driver):
+ - calls request_firmware(&fw_entry, $FIRMWARE, device)
+ - kernel searchs the fimware image with name $FIRMWARE directly
+ in the below search path of root filesystem:
+ "/lib/firmware/updates/" UTS_RELEASE,
+ "/lib/firmware/updates",
+ "/lib/firmware/" UTS_RELEASE,
+ "/lib/firmware"
+ - If found, goto 7), else goto 2)
+
+ 2), userspace:
- /sys/class/firmware/xxx/{loading,data} appear.
- hotplug gets called with a firmware identifier in $FIRMWARE
and the usual hotplug environment.
- hotplug: echo 1 > /sys/class/firmware/xxx/loading
- kernel: Discard any previous partial load.
+ 3), kernel: Discard any previous partial load.
- userspace:
+ 4), userspace:
- hotplug: cat appropriate_firmware_image > \
/sys/class/firmware/xxx/data
- kernel: grows a buffer in PAGE_SIZE increments to hold the image as it
+ 5), kernel: grows a buffer in PAGE_SIZE increments to hold the image as it
comes in.
- userspace:
+ 6), userspace:
- hotplug: echo 0 > /sys/class/firmware/xxx/loading
- kernel: request_firmware() returns and the driver has the firmware
+ 7), kernel: request_firmware() returns and the driver has the firmware
image in fw_entry->{data,size}. If something went wrong
request_firmware() returns non-zero and fw_entry is set to
NULL.
- kernel(driver): Driver code calls release_firmware(fw_entry) releasing
+ 8), kernel(driver): Driver code calls release_firmware(fw_entry) releasing
the firmware image and any related resource.
High level behavior (driver code):
BIOS and Kernel Developer's Guide (BKDG) For AMD Family 15h Processors
(not yet published)
-Author: Andreas Herrmann <andreas.herrmann3@amd.com>
+Author: Andreas Herrmann <herrmann.der.user@googlemail.com>
Description
-----------
--- /dev/null
+Chinese translated version of Documentation/IRQ.txt
+
+If you have any comment or update to the content, please contact the
+original document maintainer directly. However, if you have a problem
+communicating in English you can also ask the Chinese maintainer for
+help. Contact the Chinese maintainer if this translation is outdated
+or if there is a problem with the translation.
+
+Maintainer: Eric W. Biederman <ebiederman@xmission.com>
+Chinese maintainer: Fu Wei <tekkamanninja@gmail.com>
+---------------------------------------------------------------------
+Documentation/IRQ.txt 的中文翻译
+
+如果想评论或更新本文的内容，请直接联系原文档的维护者。如果你使用英文
+交流有困难的话，也可以向中文版维护者求助。如果本翻译更新不及时或者翻
+译存在问题，请联系中文版维护者。
+英文版维护者： Eric W. Biederman <ebiederman@xmission.com>
+中文版维护者： 傅炜 Fu Wei <tekkamanninja@gmail.com>
+中文版翻译者： 傅炜 Fu Wei <tekkamanninja@gmail.com>
+中文版校译者： 傅炜 Fu Wei <tekkamanninja@gmail.com>
+
+
+以下为正文
+---------------------------------------------------------------------
+何为 IRQ?
+
+一个 IRQ 是来自某个设备的一个中断请求。目前，它们可以来自一个硬件引脚，
+或来自一个数据包。多个设备可能连接到同个硬件引脚，从而共享一个 IRQ。
+
+一个 IRQ 编号是用于告知硬件中断源的内核标识。通常情况下，这是一个
+全局 irq_desc 数组的索引，但是除了在 linux/interrupt.h 中的实现，
+具体的细节是体系结构特定的。
+
+一个 IRQ 编号是设备上某个可能的中断源的枚举。通常情况下，枚举的编号是
+该引脚在系统内中断控制器的所有输入引脚中的编号。对于 ISA 总线中的情况，
+枚举的是在两个 i8259 中断控制器中 16 个输入引脚。
+
+架构可以对 IRQ 编号指定额外的含义，在硬件涉及任何手工配置的情况下，
+是被提倡的。ISA 的 IRQ 是一个分配这类额外含义的典型例子。
--- /dev/null
+Chinese translated version of Documentation/arm64/booting.txt
+
+If you have any comment or update to the content, please contact the
+original document maintainer directly. However, if you have a problem
+communicating in English you can also ask the Chinese maintainer for
+help. Contact the Chinese maintainer if this translation is outdated
+or if there is a problem with the translation.
+
+Maintainer: Will Deacon <will.deacon@arm.com>
+Chinese maintainer: Fu Wei <tekkamanninja@gmail.com>
+---------------------------------------------------------------------
+Documentation/arm64/booting.txt 的中文翻译
+
+如果想评论或更新本文的内容，请直接联系原文档的维护者。如果你使用英文
+交流有困难的话，也可以向中文版维护者求助。如果本翻译更新不及时或者翻
+译存在问题，请联系中文版维护者。
+
+英文版维护者： Will Deacon <will.deacon@arm.com>
+中文版维护者： 傅炜 Fu Wei <tekkamanninja@gmail.com>
+中文版翻译者： 傅炜 Fu Wei <tekkamanninja@gmail.com>
+中文版校译者： 傅炜 Fu Wei <tekkamanninja@gmail.com>
+
+以下为正文
+---------------------------------------------------------------------
+ 启动 AArch64 Linux
+ ==================
+
+作者: Will Deacon <will.deacon@arm.com>
+日期: 2012 年 09 月 07 日
+
+本文档基于 Russell King 的 ARM 启动文档，且适用于所有公开发布的
+AArch64 Linux 内核代码。
+
+AArch64 异常模型由多个异常级别（EL0 - EL3）组成，对于 EL0 和 EL1
+异常级有对应的安全和非安全模式。EL2 是系统管理级，且仅存在于
+非安全模式下。EL3 是最高特权级，且仅存在于安全模式下。
+
+基于本文档的目的，我们将简单地使用‘引导装载程序’（‘boot loader’）
+这个术语来定义在将控制权交给 Linux 内核前 CPU 上执行的所有软件。
+这可能包含安全监控和系统管理代码，或者它可能只是一些用于准备最小启动
+环境的指令。
+
+基本上，引导装载程序（至少）应实现以下操作：
+
+1、设置和初始化 RAM
+2、设置设备树数据
+3、解压内核映像
+4、调用内核映像
+
+
+1、设置和初始化 RAM
+-----------------
+
+必要性: 强制
+
+引导装载程序应该找到并初始化系统中所有内核用于保持系统变量数据的 RAM。
+这个操作的执行是设备依赖的。（它可能使用内部算法来自动定位和计算所有
+RAM，或可能使用对这个设备已知的 RAM 信息，还可能使用任何引导装载程序
+设计者想到的匹配方法。）
+
+
+2、设置设备树数据
+---------------
+
+必要性: 强制
+
+设备树数据块（dtb）大小必须不大于 2 MB，且位于从内核映像起始算起第一个
+512MB 内的 2MB 边界上。这使得内核可以通过初始页表中的单个节描述符来
+映射此数据块。
+
+
+3、解压内核映像
+-------------
+
+必要性: 可选
+
+AArch64 内核当前没有提供自解压代码，因此如果使用了压缩内核映像文件
+（比如 Image.gz），则需要通过引导装载程序（使用 gzip 等）来进行解压。
+若引导装载程序没有实现这个需求，就要使用非压缩内核映像文件。
+
+
+4、调用内核映像
+-------------
+
+必要性: 强制
+
+已解压的内核映像包含一个 32 字节的头，内容如下：
+
+ u32 magic = 0x14000008; /* 跳转到 stext, 小端 */
+ u32 res0 = 0; /* 保留 */
+ u64 text_offset; /* 映像装载偏移 */
+ u64 res1 = 0; /* 保留 */
+ u64 res2 = 0; /* 保留 */
+
+映像必须位于系统 RAM 起始处的特定偏移（当前是 0x80000）。系统 RAM
+的起始地址必须是以 2MB 对齐的。
+
+在跳转入内核前，必须符合以下状态：
+
+- 停止所有 DMA 设备，这样内存数据就不会因为虚假网络包或磁盘数据而
+ 被破坏。这可能可以节省你许多的调试时间。
+
+- 主 CPU 通用寄存器设置
+ x0 = 系统 RAM 中设备树数据块（dtb）的物理地址。
+ x1 = 0 (保留，将来可能使用)
+ x2 = 0 (保留，将来可能使用)
+ x3 = 0 (保留，将来可能使用)
+
+- CPU 模式
+ 所有形式的中断必须在 PSTATE.DAIF 中被屏蔽（Debug、SError、IRQ
+ 和 FIQ）。
+ CPU 必须处于 EL2（推荐，可访问虚拟化扩展）或非安全 EL1 模式下。
+
+- 高速缓存、MMU
+ MMU 必须关闭。
+ 指令缓存开启或关闭都可以。
+ 数据缓存必须关闭且无效。
+ 外部高速缓存（如果存在）必须配置并禁用。
+
+- 架构计时器
+ CNTFRQ 必须设定为计时器的频率。
+ 如果在 EL1 模式下进入内核，则 CNTHCTL_EL2 中的 EL1PCTEN (bit 0)
+ 必须置位。
+
+- 一致性
+ 通过内核启动的所有 CPU 在内核入口地址上必须处于相同的一致性域中。
+ 这可能要根据具体实现来定义初始化过程，以使能每个CPU上对维护操作的
+ 接收。
+
+- 系统寄存器
+ 在进入内核映像的异常级中，所有构架中可写的系统寄存器必须通过软件
+ 在一个更高的异常级别下初始化，以防止在 未知 状态下运行。
+
+引导装载程序必须在每个 CPU 处于以下状态时跳入内核入口：
+
+- 主 CPU 必须直接跳入内核映像的第一条指令。通过此 CPU 传递的设备树
+ 数据块必须在每个 CPU 节点中包含以下内容：
+
+ 1、‘enable-method’属性。目前，此字段支持的值仅为字符串“spin-table”。
+
+ 2、‘cpu-release-addr’标识一个 64-bit、初始化为零的内存位置。
+
+ 引导装载程序必须生成这些设备树属性，并在跳入内核入口之前将其插入
+ 数据块。
+
+- 任何辅助 CPU 必须在内存保留区（通过设备树中的 /memreserve/ 域传递
+ 给内核）中自旋于内核之外，轮询它们的 cpu-release-addr 位置（必须
+ 包含在保留区中）。可通过插入 wfe 指令来降低忙循环开销，而主 CPU 将
+ 发出 sev 指令。当对 cpu-release-addr 所指位置的读取操作返回非零值
+ 时，CPU 必须直接跳入此值所指向的地址。
+
+- 辅助 CPU 通用寄存器设置
+ x0 = 0 (保留，将来可能使用)
+ x1 = 0 (保留，将来可能使用)
+ x2 = 0 (保留，将来可能使用)
+ x3 = 0 (保留，将来可能使用)
--- /dev/null
+Chinese translated version of Documentation/arm64/memory.txt
+
+If you have any comment or update to the content, please contact the
+original document maintainer directly. However, if you have a problem
+communicating in English you can also ask the Chinese maintainer for
+help. Contact the Chinese maintainer if this translation is outdated
+or if there is a problem with the translation.
+
+Maintainer: Catalin Marinas <catalin.marinas@arm.com>
+Chinese maintainer: Fu Wei <tekkamanninja@gmail.com>
+---------------------------------------------------------------------
+Documentation/arm64/memory.txt 的中文翻译
+
+如果想评论或更新本文的内容，请直接联系原文档的维护者。如果你使用英文
+交流有困难的话，也可以向中文版维护者求助。如果本翻译更新不及时或者翻
+译存在问题，请联系中文版维护者。
+
+英文版维护者： Catalin Marinas <catalin.marinas@arm.com>
+中文版维护者： 傅炜 Fu Wei <tekkamanninja@gmail.com>
+中文版翻译者： 傅炜 Fu Wei <tekkamanninja@gmail.com>
+中文版校译者： 傅炜 Fu Wei <tekkamanninja@gmail.com>
+
+以下为正文
+---------------------------------------------------------------------
+ Linux 在 AArch64 中的内存布局
+ ===========================
+
+作者: Catalin Marinas <catalin.marinas@arm.com>
+日期: 2012 年 02 月 20 日
+
+本文档描述 AArch64 Linux 内核所使用的虚拟内存布局。此构架可以实现
+页大小为 4KB 的 4 级转换表和页大小为 64KB 的 3 级转换表。
+
+AArch64 Linux 使用页大小为 4KB 的 3 级转换表配置，对于用户和内核
+都有 39-bit (512GB) 的虚拟地址空间。对于页大小为 64KB的配置，仅
+使用 2 级转换表，但内存布局相同。
+
+用户地址空间的 63:39 位为 0，而内核地址空间的相应位为 1。TTBRx 的
+选择由虚拟地址的 63 位给出。swapper_pg_dir 仅包含内核（全局）映射，
+而用户 pgd 仅包含用户（非全局）映射。swapper_pgd_dir 地址被写入
+TTBR1 中，且从不写入 TTBR0。
+
+
+AArch64 Linux 内存布局：
+
+起始地址 结束地址 大小 用途
+-----------------------------------------------------------------------
+0000000000000000 0000007fffffffff 512GB 用户空间
+
+ffffff8000000000 ffffffbbfffcffff ~240GB vmalloc
+
+ffffffbbfffd0000 ffffffbcfffdffff 64KB [防护页]
+
+ffffffbbfffe0000 ffffffbcfffeffff 64KB PCI I/O 空间
+
+ffffffbbffff0000 ffffffbcffffffff 64KB [防护页]
+
+ffffffbc00000000 ffffffbdffffffff 8GB vmemmap
+
+ffffffbe00000000 ffffffbffbffffff ~8GB [防护页，未来用于 vmmemap]
+
+ffffffbffc000000 ffffffbfffffffff 64MB 模块
+
+ffffffc000000000 ffffffffffffffff 256GB 内存空间
+
+
+4KB 页大小的转换表查找：
+
++--------+--------+--------+--------+--------+--------+--------+--------+
+|63 56|55 48|47 40|39 32|31 24|23 16|15 8|7 0|
++--------+--------+--------+--------+--------+--------+--------+--------+
+ | | | | | |
+ | | | | | v
+ | | | | | [11:0] 页内偏移
+ | | | | +-> [20:12] L3 索引
+ | | | +-----------> [29:21] L2 索引
+ | | +---------------------> [38:30] L1 索引
+ | +-------------------------------> [47:39] L0 索引 (未使用)
+ +-------------------------------------------------> [63] TTBR0/1
+
+
+64KB 页大小的转换表查找：
+
++--------+--------+--------+--------+--------+--------+--------+--------+
+|63 56|55 48|47 40|39 32|31 24|23 16|15 8|7 0|
++--------+--------+--------+--------+--------+--------+--------+--------+
+ | | | | |
+ | | | | v
+ | | | | [15:0] 页内偏移
+ | | | +----------> [28:16] L3 索引
+ | | +--------------------------> [41:29] L2 索引 (仅使用 38:29 )
+ | +-------------------------------> [47:42] L1 索引 (未使用)
+ +-------------------------------------------------> [63] TTBR0/1
F: include/linux/altera_jtaguart.h
AMD FAM15H PROCESSOR POWER MONITORING DRIVER
-M: Andreas Herrmann <andreas.herrmann3@amd.com>
+M: Andreas Herrmann <herrmann.der.user@googlemail.com>
L: lm-sensors@lm-sensors.org
S: Maintained
F: Documentation/hwmon/fam15h_power
S: Maintained
F: arch/arm/
+ARM SUB-ARCHITECTURES
+L: linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
+S: MAINTAINED
+F: arch/arm/mach-*/
+F: arch/arm/plat-*/
+T: git git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc.git
+
ARM PRIMECELL AACI PL041 DRIVER
M: Russell King <linux@arm.linux.org.uk>
S: Maintained
EXTENSIBLE FIRMWARE INTERFACE (EFI)
M: Matt Fleming <matt.fleming@intel.com>
L: linux-efi@vger.kernel.org
+T: git git://git.kernel.org/pub/scm/linux/kernel/git/mfleming/efi.git
S: Maintained
F: Documentation/x86/efi-stub.txt
F: arch/ia64/kernel/efi.c
S: Odd Fixes
F: drivers/net/
F: include/linux/if_*
-F: include/linux/*device.h
+F: include/linux/netdevice.h
+F: include/linux/arcdevice.h
+F: include/linux/etherdevice.h
+F: include/linux/fcdevice.h
+F: include/linux/fddidevice.h
+F: include/linux/hippidevice.h
+F: include/linux/inetdevice.h
NETXEN (1/10) GbE SUPPORT
M: Sony Chacko <sony.chacko@qlogic.com>
F: drivers/pinctrl/spear/
PKTCDVD DRIVER
-M: Peter Osterlund <petero2@telia.com>
+M: Jiri Kosina <jkosina@suse.cz>
S: Maintained
F: drivers/block/pktcdvd.c
F: include/linux/pktcdvd.h
VERSION = 3
PATCHLEVEL = 7
SUBLEVEL = 0
-EXTRAVERSION = -rc2
+EXTRAVERSION = -rc3
NAME = Terrified Chipmunk
# *DOCUMENTATION*
#include <asm/processor.h>
#include <asm/types.h>
#include <asm/hwrpb.h>
+#include <asm/sysinfo.h>
#endif
#ifndef __ASSEMBLY__
mm_segment_t addr_limit; /* thread address space */
unsigned cpu; /* current CPU */
int preempt_count; /* 0 => preemptable, <0 => BUG */
+ unsigned int status; /* thread-synchronous flags */
int bpt_nsaved;
unsigned long bpt_addr[2]; /* breakpoint handling */
* - these are process state flags and used from assembly
* - pending work-to-be-done flags come first and must be assigned to be
* within bits 0 to 7 to fit in and immediate operand.
- * - ALPHA_UAC_SHIFT below must be kept consistent with the unaligned
- * control flags.
*
* TIF_SYSCALL_TRACE is known to be 0 via blbs.
*/
#define TIF_NOTIFY_RESUME 1 /* callback before returning to user */
#define TIF_SIGPENDING 2 /* signal pending */
#define TIF_NEED_RESCHED 3 /* rescheduling necessary */
-#define TIF_POLLING_NRFLAG 8 /* poll_idle is polling NEED_RESCHED */
#define TIF_DIE_IF_KERNEL 9 /* dik recursion lock */
-#define TIF_UAC_NOPRINT 10 /* ! Preserve sequence of following */
-#define TIF_UAC_NOFIX 11 /* ! flags as they match */
-#define TIF_UAC_SIGBUS 12 /* ! userspace part of 'osf_sysinfo' */
#define TIF_MEMDIE 13 /* is terminating due to OOM killer */
-#define TIF_RESTORE_SIGMASK 14 /* restore signal mask in do_signal */
#define _TIF_SYSCALL_TRACE (1<<TIF_SYSCALL_TRACE)
#define _TIF_SIGPENDING (1<<TIF_SIGPENDING)
#define _TIF_NEED_RESCHED (1<<TIF_NEED_RESCHED)
-#define _TIF_POLLING_NRFLAG (1<<TIF_POLLING_NRFLAG)
#define _TIF_NOTIFY_RESUME (1<<TIF_NOTIFY_RESUME)
/* Work to do on interrupt/exception return. */
#define _TIF_ALLWORK_MASK (_TIF_WORK_MASK \
| _TIF_SYSCALL_TRACE)
-#define ALPHA_UAC_SHIFT TIF_UAC_NOPRINT
-#define ALPHA_UAC_MASK (1 << TIF_UAC_NOPRINT | 1 << TIF_UAC_NOFIX | \
- 1 << TIF_UAC_SIGBUS)
+#define TS_UAC_NOPRINT 0x0001 /* ! Preserve the following three */
+#define TS_UAC_NOFIX 0x0002 /* ! flags as they match */
+#define TS_UAC_SIGBUS 0x0004 /* ! userspace part of 'osf_sysinfo' */
+#define TS_RESTORE_SIGMASK 0x0008 /* restore signal mask in do_signal() */
+#define TS_POLLING 0x0010 /* idle task polling need_resched,
+ skip sending interrupt */
-#define SET_UNALIGN_CTL(task,value) ({ \
- task_thread_info(task)->flags = ((task_thread_info(task)->flags & \
- ~ALPHA_UAC_MASK) \
- | (((value) << ALPHA_UAC_SHIFT) & (1<<TIF_UAC_NOPRINT))\
- | (((value) << (ALPHA_UAC_SHIFT + 1)) & (1<<TIF_UAC_SIGBUS)) \
- | (((value) << (ALPHA_UAC_SHIFT - 1)) & (1<<TIF_UAC_NOFIX)));\
+#define tsk_is_polling(t) (task_thread_info(t)->status & TS_POLLING)
+
+#ifndef __ASSEMBLY__
+#define HAVE_SET_RESTORE_SIGMASK 1
+static inline void set_restore_sigmask(void)
+{
+ struct thread_info *ti = current_thread_info();
+ ti->status |= TS_RESTORE_SIGMASK;
+ WARN_ON(!test_bit(TIF_SIGPENDING, (unsigned long *)&ti->flags));
+}
+static inline void clear_restore_sigmask(void)
+{
+ current_thread_info()->status &= ~TS_RESTORE_SIGMASK;
+}
+static inline bool test_restore_sigmask(void)
+{
+ return current_thread_info()->status & TS_RESTORE_SIGMASK;
+}
+static inline bool test_and_clear_restore_sigmask(void)
+{
+ struct thread_info *ti = current_thread_info();
+ if (!(ti->status & TS_RESTORE_SIGMASK))
+ return false;
+ ti->status &= ~TS_RESTORE_SIGMASK;
+ return true;
+}
+#endif
+
+#define SET_UNALIGN_CTL(task,value) ({ \
+ __u32 status = task_thread_info(task)->status & ~UAC_BITMASK; \
+ if (value & PR_UNALIGN_NOPRINT) \
+ status |= TS_UAC_NOPRINT; \
+ if (value & PR_UNALIGN_SIGBUS) \
+ status |= TS_UAC_SIGBUS; \
+ if (value & 4) /* alpha-specific */ \
+ status |= TS_UAC_NOFIX; \
+ task_thread_info(task)->status = status; \
0; })
#define GET_UNALIGN_CTL(task,value) ({ \
- put_user((task_thread_info(task)->flags & (1 << TIF_UAC_NOPRINT))\
- >> ALPHA_UAC_SHIFT \
- | (task_thread_info(task)->flags & (1 << TIF_UAC_SIGBUS))\
- >> (ALPHA_UAC_SHIFT + 1) \
- | (task_thread_info(task)->flags & (1 << TIF_UAC_NOFIX))\
- >> (ALPHA_UAC_SHIFT - 1), \
- (int __user *)(value)); \
+ __u32 status = task_thread_info(task)->status & ~UAC_BITMASK; \
+ __u32 res = 0; \
+ if (status & TS_UAC_NOPRINT) \
+ res |= PR_UNALIGN_NOPRINT; \
+ if (status & TS_UAC_SIGBUS) \
+ res |= PR_UNALIGN_SIGBUS; \
+ if (status & TS_UAC_NOFIX) \
+ res |= 4; \
+ put_user(res, (int __user *)(value)); \
})
-#define tsk_is_polling(t) test_tsk_thread_flag(t, TIF_POLLING_NRFLAG)
-
#endif /* __KERNEL__ */
#endif /* _ALPHA_THREAD_INFO_H */
case GSI_UACPROC:
if (nbytes < sizeof(unsigned int))
return -EINVAL;
- w = (current_thread_info()->flags >> ALPHA_UAC_SHIFT) &
- UAC_BITMASK;
+ w = current_thread_info()->status & UAC_BITMASK;
if (put_user(w, (unsigned int __user *)buffer))
return -EFAULT;
return 1;
break;
case SSI_NVPAIRS: {
- unsigned long v, w, i;
- unsigned int old, new;
+ unsigned __user *p = buffer;
+ unsigned i;
- for (i = 0; i < nbytes; ++i) {
+ for (i = 0, p = buffer; i < nbytes; ++i, p += 2) {
+ unsigned v, w, status;
- if (get_user(v, 2*i + (unsigned int __user *)buffer))
- return -EFAULT;
- if (get_user(w, 2*i + 1 + (unsigned int __user *)buffer))
+ if (get_user(v, p) || get_user(w, p + 1))
return -EFAULT;
switch (v) {
case SSIN_UACPROC:
- again:
- old = current_thread_info()->flags;
- new = old & ~(UAC_BITMASK << ALPHA_UAC_SHIFT);
- new = new | (w & UAC_BITMASK) << ALPHA_UAC_SHIFT;
- if (cmpxchg(¤t_thread_info()->flags,
- old, new) != old)
- goto again;
+ w &= UAC_BITMASK;
+ status = current_thread_info()->status;
+ status = (status & ~UAC_BITMASK) | w;
+ current_thread_info()->status = status;
break;
default:
void
cpu_idle(void)
{
- set_thread_flag(TIF_POLLING_NRFLAG);
+ current_thread_info()->status |= TS_POLLING;
while (1) {
/* FIXME -- EV6 and LCA45 know how to power down
/* Check the UAC bits to decide what the user wants us to do
with the unaliged access. */
- if (!test_thread_flag (TIF_UAC_NOPRINT)) {
+ if (!(current_thread_info()->status & TS_UAC_NOPRINT)) {
if (__ratelimit(&ratelimit)) {
printk("%s(%d): unaligned trap at %016lx: %p %lx %ld\n",
current->comm, task_pid_nr(current),
regs->pc - 4, va, opcode, reg);
}
}
- if (test_thread_flag (TIF_UAC_SIGBUS))
+ if ((current_thread_info()->status & TS_UAC_SIGBUS))
goto give_sigbus;
/* Not sure why you'd want to use this, but... */
- if (test_thread_flag (TIF_UAC_NOFIX))
+ if ((current_thread_info()->status & TS_UAC_NOFIX))
return;
/* Don't bother reading ds in the access check since we already
default "4"
config HOTPLUG_CPU
- bool "Support for hot-pluggable CPUs (EXPERIMENTAL)"
- depends on SMP && HOTPLUG && EXPERIMENTAL
+ bool "Support for hot-pluggable CPUs"
+ depends on SMP && HOTPLUG
help
Say Y here to experiment with turning CPUs off and on. CPUs
can be controlled through /sys/devices/system/cpu.
default 100
config THUMB2_KERNEL
- bool "Compile the kernel in Thumb-2 mode (EXPERIMENTAL)"
- depends on CPU_V7 && !CPU_V6 && !CPU_V6K && EXPERIMENTAL
+ bool "Compile the kernel in Thumb-2 mode"
+ depends on CPU_V7 && !CPU_V6 && !CPU_V6K
select AEABI
select ARM_ASM_UNIFIED
select ARM_UNWIND
config XEN
bool "Xen guest support on ARM (EXPERIMENTAL)"
depends on EXPERIMENTAL && ARM && OF
+ depends on CPU_V7 && !CPU_V6
help
Say Y if you want to run Linux in a Virtual Machine on Xen on ARM.
OBJCOPYFLAGS :=-O binary -R .comment -S
GZFLAGS :=-9
#KBUILD_CFLAGS +=-pipe
-# Explicitly specifiy 32-bit ARM ISA since toolchain default can be -mthumb:
-KBUILD_CFLAGS +=$(call cc-option,-marm,)
# Never generate .eh_frame
KBUILD_CFLAGS += $(call cc-option,-fno-dwarf2-cfi-asm)
ifeq ($(CONFIG_THUMB2_KERNEL),y)
AFLAGS_AUTOIT :=$(call as-option,-Wa$(comma)-mimplicit-it=always,-Wa$(comma)-mauto-it)
AFLAGS_NOWARN :=$(call as-option,-Wa$(comma)-mno-warn-deprecated,-Wa$(comma)-W)
-CFLAGS_THUMB2 :=-mthumb $(AFLAGS_AUTOIT) $(AFLAGS_NOWARN)
-AFLAGS_THUMB2 :=$(CFLAGS_THUMB2) -Wa$(comma)-mthumb
+CFLAGS_ISA :=-mthumb $(AFLAGS_AUTOIT) $(AFLAGS_NOWARN)
+AFLAGS_ISA :=$(CFLAGS_ISA) -Wa$(comma)-mthumb
# Work around buggy relocation from gas if requested:
ifeq ($(CONFIG_THUMB2_AVOID_R_ARM_THM_JUMP11),y)
CFLAGS_MODULE +=-fno-optimize-sibling-calls
endif
+else
+CFLAGS_ISA :=$(call cc-option,-marm,)
+AFLAGS_ISA :=$(CFLAGS_ISA)
endif
# Need -Uarm for gcc < 3.x
-KBUILD_CFLAGS +=$(CFLAGS_ABI) $(CFLAGS_THUMB2) $(arch-y) $(tune-y) $(call cc-option,-mshort-load-bytes,$(call cc-option,-malignment-traps,)) -msoft-float -Uarm
-KBUILD_AFLAGS +=$(CFLAGS_ABI) $(AFLAGS_THUMB2) $(arch-y) $(tune-y) -include asm/unified.h -msoft-float
+KBUILD_CFLAGS +=$(CFLAGS_ABI) $(CFLAGS_ISA) $(arch-y) $(tune-y) $(call cc-option,-mshort-load-bytes,$(call cc-option,-malignment-traps,)) -msoft-float -Uarm
+KBUILD_AFLAGS +=$(CFLAGS_ABI) $(AFLAGS_ISA) $(arch-y) $(tune-y) -include asm/unified.h -msoft-float
CHECKFLAGS += -D__arm__
$(obj)/xipImage: vmlinux FORCE
$(call if_changed,objcopy)
- @echo ' Kernel: $@ is ready (physical address: $(CONFIG_XIP_PHYS_ADDR))'
+ $(kecho) ' Kernel: $@ is ready (physical address: $(CONFIG_XIP_PHYS_ADDR))'
$(obj)/Image $(obj)/zImage: FORCE
@echo 'Kernel configured for XIP (CONFIG_XIP_KERNEL=y)'
$(obj)/Image: vmlinux FORCE
$(call if_changed,objcopy)
- @echo ' Kernel: $@ is ready'
+ $(kecho) ' Kernel: $@ is ready'
$(obj)/compressed/vmlinux: $(obj)/Image FORCE
$(Q)$(MAKE) $(build)=$(obj)/compressed $@
$(obj)/zImage: $(obj)/compressed/vmlinux FORCE
$(call if_changed,objcopy)
- @echo ' Kernel: $@ is ready'
+ $(kecho) ' Kernel: $@ is ready'
endif
$(obj)/uImage: $(obj)/zImage FORCE
@$(check_for_multiple_loadaddr)
$(call if_changed,uimage)
- @echo ' Image $@ is ready'
+ $(kecho) ' Image $@ is ready'
$(obj)/bootp/bootp: $(obj)/zImage initrd FORCE
$(Q)$(MAKE) $(build)=$(obj)/bootp $@
$(obj)/bootpImage: $(obj)/bootp/bootp FORCE
$(call if_changed,objcopy)
- @echo ' Kernel: $@ is ready'
+ $(kecho) ' Kernel: $@ is ready'
PHONY += initrd FORCE
initrd:
#size-cells = <0>;
btn3 {
- label = "Buttin 3";
+ label = "Button 3";
gpios = <&pioA 30 1>;
linux,code = <0x103>;
gpio-key,wakeup;
};
btn4 {
- label = "Buttin 4";
+ label = "Button 4";
gpios = <&pioA 31 1>;
linux,code = <0x104>;
gpio-key,wakeup;
compatible = "stericsson,db8500-i2c", "st,nomadik-i2c", "arm,primecell";
reg = <0x80004000 0x1000>;
interrupts = <0 21 0x4>;
+ arm,primecell-periphid = <0x180024>;
+
#address-cells = <1>;
#size-cells = <0>;
v-i2c-supply = <&db8500_vape_reg>;
compatible = "stericsson,db8500-i2c", "st,nomadik-i2c", "arm,primecell";
reg = <0x80122000 0x1000>;
interrupts = <0 22 0x4>;
+ arm,primecell-periphid = <0x180024>;
+
#address-cells = <1>;
#size-cells = <0>;
v-i2c-supply = <&db8500_vape_reg>;
compatible = "stericsson,db8500-i2c", "st,nomadik-i2c", "arm,primecell";
reg = <0x80128000 0x1000>;
interrupts = <0 55 0x4>;
+ arm,primecell-periphid = <0x180024>;
+
#address-cells = <1>;
#size-cells = <0>;
v-i2c-supply = <&db8500_vape_reg>;
compatible = "stericsson,db8500-i2c", "st,nomadik-i2c", "arm,primecell";
reg = <0x80110000 0x1000>;
interrupts = <0 12 0x4>;
+ arm,primecell-periphid = <0x180024>;
+
#address-cells = <1>;
#size-cells = <0>;
v-i2c-supply = <&db8500_vape_reg>;
compatible = "stericsson,db8500-i2c", "st,nomadik-i2c", "arm,primecell";
reg = <0x8012a000 0x1000>;
interrupts = <0 51 0x4>;
+ arm,primecell-periphid = <0x180024>;
+
#address-cells = <1>;
#size-cells = <0>;
v-i2c-supply = <&db8500_vape_reg>;
interrupts = <0 60 0x4>;
status = "disabled";
};
+
sdi@80118000 {
compatible = "arm,pl18x", "arm,primecell";
reg = <0x80118000 0x1000>;
interrupts = <0 50 0x4>;
status = "disabled";
};
+
sdi@80005000 {
compatible = "arm,pl18x", "arm,primecell";
reg = <0x80005000 0x1000>;
interrupts = <0 41 0x4>;
status = "disabled";
};
+
sdi@80119000 {
compatible = "arm,pl18x", "arm,primecell";
reg = <0x80119000 0x1000>;
interrupts = <0 59 0x4>;
status = "disabled";
};
+
sdi@80114000 {
compatible = "arm,pl18x", "arm,primecell";
reg = <0x80114000 0x1000>;
interrupts = <0 99 0x4>;
status = "disabled";
};
+
sdi@80008000 {
compatible = "arm,pl18x", "arm,primecell";
- reg = <0x80114000 0x1000>;
+ reg = <0x80008000 0x1000>;
interrupts = <0 100 0x4>;
status = "disabled";
};
compatible = "samsung,trats", "samsung,exynos4210";
memory {
- reg = <0x40000000 0x20000000
- 0x60000000 0x20000000>;
+ reg = <0x40000000 0x10000000
+ 0x50000000 0x10000000
+ 0x60000000 0x10000000
+ 0x70000000 0x10000000>;
};
chosen {
interrupts = <13>, <56>;
interrupt-names = "gpmi-dma", "bch";
clocks = <&clks 34>;
+ clock-names = "gpmi_io";
fsl,gpmi-dma-channel = <4>;
status = "disabled";
};
interrupts = <88>, <41>;
interrupt-names = "gpmi-dma", "bch";
clocks = <&clks 50>;
+ clock-names = "gpmi_io";
fsl,gpmi-dma-channel = <4>;
status = "disabled";
};
interrupt-names = "common", "tx", "rx", "sidetone";
interrupt-parent = <&intc>;
ti,buffer-size = <1280>;
- ti,hwmods = "mcbsp2";
+ ti,hwmods = "mcbsp2", "mcbsp2_sidetone";
};
mcbsp3: mcbsp@49024000 {
interrupt-names = "common", "tx", "rx", "sidetone";
interrupt-parent = <&intc>;
ti,buffer-size = <128>;
- ti,hwmods = "mcbsp3";
+ ti,hwmods = "mcbsp3", "mcbsp3_sidetone";
};
mcbsp4: mcbsp@49026000 {
CONFIG_SPI=y
CONFIG_SPI_IMX=y
CONFIG_GPIO_SYSFS=y
+CONFIG_GPIO_MC9S08DZ60=y
# CONFIG_HWMON is not set
CONFIG_WATCHDOG=y
CONFIG_IMX2_WDT=y
CONFIG_SOC_CAMERA_OV2640=y
CONFIG_VIDEO_MX3=y
CONFIG_FB=y
+CONFIG_LCD_PLATFORM=y
CONFIG_BACKLIGHT_LCD_SUPPORT=y
CONFIG_LCD_CLASS_DEVICE=y
CONFIG_LCD_L4F00242T03=y
CONFIG_EXPERIMENTAL=y
CONFIG_SYSVIPC=y
-CONFIG_NO_HZ=y
+CONFIG_IRQ_DOMAIN_DEBUG=y
CONFIG_HIGH_RES_TIMERS=y
CONFIG_LOG_BUF_SHIFT=14
CONFIG_BLK_DEV_INITRD=y
CONFIG_MODULES=y
CONFIG_MODULE_UNLOAD=y
CONFIG_ARCH_MVEBU=y
-CONFIG_MACH_ARMADA_370_XP=y
+CONFIG_MACH_ARMADA_370=y
+CONFIG_MACH_ARMADA_XP=y
+# CONFIG_CACHE_L2X0 is not set
CONFIG_AEABI=y
CONFIG_HIGHMEM=y
-CONFIG_USE_OF=y
+# CONFIG_COMPACTION is not set
CONFIG_ZBOOT_ROM_TEXT=0x0
CONFIG_ZBOOT_ROM_BSS=0x0
CONFIG_ARM_APPENDED_DTB=y
CONFIG_SERIAL_OF_PLATFORM=y
CONFIG_GPIOLIB=y
CONFIG_GPIO_SYSFS=y
+# CONFIG_USB_SUPPORT is not set
+# CONFIG_IOMMU_SUPPORT is not set
CONFIG_EXT2_FS=y
CONFIG_EXT3_FS=y
# CONFIG_EXT3_FS_XATTR is not set
+CONFIG_ARCH_VERSATILE=y
CONFIG_EXPERIMENTAL=y
# CONFIG_LOCALVERSION_AUTO is not set
CONFIG_SYSVIPC=y
#define flat_argvp_envp_on_stack() 1
#define flat_old_ram_flag(flags) (flags)
#define flat_reloc_valid(reloc, size) ((reloc) <= (size))
-#define flat_get_addr_from_rp(rp, relval, flags, persistent) get_unaligned(rp)
+#define flat_get_addr_from_rp(rp, relval, flags, persistent) ((void)persistent,get_unaligned(rp))
#define flat_put_addr_at_rp(rp, val, relval) put_unaligned(val,rp)
#define flat_get_relocate_addr(rel) (rel)
#define flat_set_persistent(relval, p) 0
#define USER_DS KERNEL_DS
#define segment_eq(a,b) (1)
-#define __addr_ok(addr) (1)
-#define __range_ok(addr,size) (0)
+#define __addr_ok(addr) ((void)(addr),1)
+#define __range_ok(addr,size) ((void)(addr),0)
#define get_fs() (KERNEL_DS)
static inline void set_fs(mm_segment_t fs)
#ifndef __ASSEMBLY__
/* Explicitly size integers that represent pfns in the interface with
- * Xen so that we can have one ABI that works for 32 and 64 bit guests. */
+ * Xen so that we can have one ABI that works for 32 and 64 bit guests.
+ * Note that this means that the xen_pfn_t type may be capable of
+ * representing pfn's which the guest cannot represent in its own pfn
+ * type. However since pfn space is controlled by the guest this is
+ * fine since it simply wouldn't be able to create any sure pfns in
+ * the first place.
+ */
typedef uint64_t xen_pfn_t;
+#define PRI_xen_pfn "llx"
typedef uint64_t xen_ulong_t;
+#define PRI_xen_ulong "llx"
/* Guest handles for primitive C types. */
__DEFINE_GUEST_HANDLE(uchar, unsigned char);
__DEFINE_GUEST_HANDLE(uint, unsigned int);
-__DEFINE_GUEST_HANDLE(ulong, unsigned long);
DEFINE_GUEST_HANDLE(char);
DEFINE_GUEST_HANDLE(int);
-DEFINE_GUEST_HANDLE(long);
DEFINE_GUEST_HANDLE(void);
DEFINE_GUEST_HANDLE(uint64_t);
DEFINE_GUEST_HANDLE(uint32_t);
#include <xen/interface/grant_table.h>
#define pfn_to_mfn(pfn) (pfn)
-#define phys_to_machine_mapping_valid (1)
+#define phys_to_machine_mapping_valid(pfn) (1)
#define mfn_to_pfn(mfn) (mfn)
#define mfn_to_virt(m) (__va(mfn_to_pfn(m) << PAGE_SHIFT))
#define XMADDR(x) ((xmaddr_t) { .maddr = (x) })
#define XPADDR(x) ((xpaddr_t) { .paddr = (x) })
+#define INVALID_P2M_ENTRY (~0UL)
+
static inline xmaddr_t phys_to_machine(xpaddr_t phys)
{
unsigned offset = phys.paddr & ~PAGE_MASK;
return 0;
}
+static inline bool __set_phys_to_machine(unsigned long pfn, unsigned long mfn)
+{
+ BUG_ON(pfn != mfn && mfn != INVALID_P2M_ENTRY);
+ return true;
+}
+
static inline bool set_phys_to_machine(unsigned long pfn, unsigned long mfn)
{
- BUG();
- return false;
+ return __set_phys_to_machine(pfn, mfn);
}
#endif /* _ASM_ARM_XEN_PAGE_H */
--- /dev/null
+/*
+ * Copyright (c) 2011 Picochip Ltd., Jamie Iles
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ * Derived from arch/arm/mach-davinci/include/mach/debug-macro.S to use 32-bit
+ * accesses to the 8250.
+ */
+
+#include <linux/serial_reg.h>
+
+ .macro senduart,rd,rx
+ str \rd, [\rx, #UART_TX << UART_SHIFT]
+ .endm
+
+ .macro busyuart,rd,rx
+1002: ldr \rd, [\rx, #UART_LSR << UART_SHIFT]
+ and \rd, \rd, #UART_LSR_TEMT | UART_LSR_THRE
+ teq \rd, #UART_LSR_TEMT | UART_LSR_THRE
+ bne 1002b
+ .endm
+
+ /* The UART's don't have any flow control IO's wired up. */
+ .macro waituart,rd,rx
+ .endm
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*
- * Derived from arch/arm/mach-davinci/include/mach/debug-macro.S to use 32-bit
- * accesses to the 8250.
*/
-#include <linux/serial_reg.h>
#define UART_SHIFT 2
#define PICOXCELL_UART1_BASE 0x80230000
ldr \rp, =PICOXCELL_UART1_BASE
.endm
- .macro senduart,rd,rx
- str \rd, [\rx, #UART_TX << UART_SHIFT]
- .endm
-
- .macro busyuart,rd,rx
-1002: ldr \rd, [\rx, #UART_LSR << UART_SHIFT]
- and \rd, \rd, #UART_LSR_TEMT | UART_LSR_THRE
- teq \rd, #UART_LSR_TEMT | UART_LSR_THRE
- bne 1002b
- .endm
-
- /* The UART's don't have any flow control IO's wired up. */
- .macro waituart,rd,rx
- .endm
+#include "8250_32.S"
* published by the Free Software Foundation.
*/
+#define UART_SHIFT 2
+#define DEBUG_LL_UART_OFFSET 0x00002000
+
.macro addruart, rp, rv, tmp
mov \rp, #DEBUG_LL_UART_OFFSET
orr \rp, \rp, #0x00c00000
orr \rp, \rp, #0xff000000 @ physical base
.endm
+#include "8250_32.S"
+
#include <linux/list.h>
#include <linux/kallsyms.h>
#include <linux/proc_fs.h>
+#include <linux/export.h>
#include <asm/exception.h>
#include <asm/mach/arch.h>
/* Order is clear bits in "clr" then set bits in "set" */
irq_modify_status(irq, clr, set & ~clr);
}
+EXPORT_SYMBOL_GPL(set_irq_flags);
void __init init_IRQ(void)
{
TEST_UNSUPPORTED(".word 0xe04f0392 @ umaal r0, pc, r2, r3")
TEST_UNSUPPORTED(".word 0xe0500090 @ undef")
TEST_UNSUPPORTED(".word 0xe05fff9f @ undef")
+#endif
+#if __LINUX_ARM_ARCH__ >= 7
TEST_RRR( "mls r0, r",1, VAL1,", r",2, VAL2,", r",3, VAL3,"")
TEST_RRR( "mlshi r7, r",8, VAL3,", r",9, VAL1,", r",10, VAL2,"")
TEST_RR( "mls lr, r",1, VAL2,", r",2, VAL3,", r13")
TEST_UNSUPPORTED(".word 0xe1700090") /* Unallocated space */
#if __LINUX_ARM_ARCH__ >= 6
TEST_UNSUPPORTED("ldrex r2, [sp]")
+#endif
+#if (__LINUX_ARM_ARCH__ >= 7) || defined(CONFIG_CPU_32v6K)
TEST_UNSUPPORTED("strexd r0, r2, r3, [sp]")
TEST_UNSUPPORTED("ldrexd r2, r3, [sp]")
TEST_UNSUPPORTED("strexb r0, r2, [sp]")
for (i = 0; i < image->nr_segments; i++) {
current_segment = &image->segment[i];
- err = memblock_is_region_memory(current_segment->mem,
- current_segment->memsz);
- if (err)
- return - EINVAL;
+ if (!memblock_is_region_memory(current_segment->mem,
+ current_segment->memsz))
+ return -EINVAL;
err = get_user(header, (__be32*)current_segment->buf);
if (err)
s64 period = hwc->sample_period;
int ret = 0;
+ /* The period may have been changed by PERF_EVENT_IOC_PERIOD */
+ if (unlikely(period != hwc->last_period))
+ left = period - (hwc->last_period - left);
+
if (unlikely(left <= -period)) {
left = period;
local64_set(&hwc->period_left, left);
asmlinkage void __cpuinit secondary_start_kernel(void)
{
struct mm_struct *mm = &init_mm;
- unsigned int cpu = smp_processor_id();
+ unsigned int cpu;
+
+ /*
+ * The identity mapping is uncached (strongly ordered), so
+ * switch away from it before attempting any exclusive accesses.
+ */
+ cpu_switch_mm(mm->pgd, mm);
+ enter_lazy_tlb(mm, current);
+ local_flush_tlb_all();
/*
* All kernel threads share the same mm context; grab a
* reference and switch to it.
*/
+ cpu = smp_processor_id();
atomic_inc(&mm->mm_count);
current->active_mm = mm;
cpumask_set_cpu(cpu, mm_cpumask(mm));
- cpu_switch_mm(mm->pgd, mm);
- enter_lazy_tlb(mm, current);
- local_flush_tlb_all();
printk("CPU%u: Booted secondary processor\n", cpu);
switch (mode) {
case CLOCK_EVT_MODE_PERIODIC:
- /* timer load already set up */
ctrl = TWD_TIMER_CONTROL_ENABLE | TWD_TIMER_CONTROL_IT_ENABLE
| TWD_TIMER_CONTROL_PERIODIC;
- __raw_writel(twd_timer_rate / HZ, twd_base + TWD_TIMER_LOAD);
+ __raw_writel(DIV_ROUND_CLOSEST(twd_timer_rate, HZ),
+ twd_base + TWD_TIMER_LOAD);
break;
case CLOCK_EVT_MODE_ONESHOT:
/* period set, and timer enabled in 'next_event' hook */
*timer_val = delay_timer->read_current_timer();
return 0;
}
+EXPORT_SYMBOL_GPL(read_current_timer);
static void __timer_delay(unsigned long cycles)
{
bool
select CPU_ARM926T
select GENERIC_CLOCKEVENTS
+ select MULTI_IRQ_HANDLER
+ select SPARSE_IRQ
menu "Atmel AT91 System-on-Chip"
comment "Atmel AT91 Processor"
-config SOC_AT91SAM9
- bool
- select AT91_SAM9_SMC
- select AT91_SAM9_TIME
- select CPU_ARM926T
- select MULTI_IRQ_HANDLER
- select SPARSE_IRQ
-
config SOC_AT91RM9200
bool "AT91RM9200"
select CPU_ARM920T
CLKDEV_CON_DEV_ID("pclk", "ssc.0", &ssc0_clk),
CLKDEV_CON_DEV_ID("pclk", "ssc.1", &ssc1_clk),
CLKDEV_CON_DEV_ID("pclk", "ssc.2", &ssc2_clk),
- CLKDEV_CON_DEV_ID(NULL, "i2c-at91rm9200", &twi_clk),
+ CLKDEV_CON_DEV_ID(NULL, "i2c-at91rm9200.0", &twi_clk),
/* fake hclk clock */
CLKDEV_CON_DEV_ID("hclk", "at91_ohci", &ohci_clk),
CLKDEV_CON_ID("pioA", &pioA_clk),
static struct platform_device at91rm9200_twi_device = {
.name = "i2c-gpio",
- .id = -1,
+ .id = 0,
.dev.platform_data = &pdata,
};
static struct platform_device at91rm9200_twi_device = {
.name = "i2c-at91rm9200",
- .id = -1,
+ .id = 0,
.resource = twi_resources,
.num_resources = ARRAY_SIZE(twi_resources),
};
CLKDEV_CON_DEV_ID("t1_clk", "atmel_tcb.1", &tc4_clk),
CLKDEV_CON_DEV_ID("t2_clk", "atmel_tcb.1", &tc5_clk),
CLKDEV_CON_DEV_ID("pclk", "ssc.0", &ssc_clk),
- CLKDEV_CON_DEV_ID(NULL, "i2c-at91sam9260", &twi_clk),
- CLKDEV_CON_DEV_ID(NULL, "i2c-at91sam9g20", &twi_clk),
+ CLKDEV_CON_DEV_ID(NULL, "i2c-at91sam9260.0", &twi_clk),
+ CLKDEV_CON_DEV_ID(NULL, "i2c-at91sam9g20.0", &twi_clk),
/* more usart lookup table for DT entries */
CLKDEV_CON_DEV_ID("usart", "fffff200.serial", &mck),
CLKDEV_CON_DEV_ID("usart", "fffb0000.serial", &usart0_clk),
static struct platform_device at91sam9260_twi_device = {
.name = "i2c-gpio",
- .id = -1,
+ .id = 0,
.dev.platform_data = &pdata,
};
};
static struct platform_device at91sam9260_twi_device = {
- .id = -1,
+ .id = 0,
.resource = twi_resources,
.num_resources = ARRAY_SIZE(twi_resources),
};
CLKDEV_CON_DEV_ID("pclk", "ssc.1", &ssc1_clk),
CLKDEV_CON_DEV_ID("pclk", "ssc.2", &ssc2_clk),
CLKDEV_CON_DEV_ID("hclk", "at91_ohci", &hck0),
- CLKDEV_CON_DEV_ID(NULL, "i2c-at91sam9261", &twi_clk),
- CLKDEV_CON_DEV_ID(NULL, "i2c-at91sam9g10", &twi_clk),
+ CLKDEV_CON_DEV_ID(NULL, "i2c-at91sam9261.0", &twi_clk),
+ CLKDEV_CON_DEV_ID(NULL, "i2c-at91sam9g10.0", &twi_clk),
CLKDEV_CON_ID("pioA", &pioA_clk),
CLKDEV_CON_ID("pioB", &pioB_clk),
CLKDEV_CON_ID("pioC", &pioC_clk),
static struct platform_device at91sam9261_twi_device = {
.name = "i2c-gpio",
- .id = -1,
+ .id = 0,
.dev.platform_data = &pdata,
};
};
static struct platform_device at91sam9261_twi_device = {
- .id = -1,
+ .id = 0,
.resource = twi_resources,
.num_resources = ARRAY_SIZE(twi_resources),
};
CLKDEV_CON_DEV_ID("spi_clk", "atmel_spi.0", &spi0_clk),
CLKDEV_CON_DEV_ID("spi_clk", "atmel_spi.1", &spi1_clk),
CLKDEV_CON_DEV_ID("t0_clk", "atmel_tcb.0", &tcb_clk),
- CLKDEV_CON_DEV_ID(NULL, "i2c-at91sam9260", &twi_clk),
+ CLKDEV_CON_DEV_ID(NULL, "i2c-at91sam9260.0", &twi_clk),
/* fake hclk clock */
CLKDEV_CON_DEV_ID("hclk", "at91_ohci", &ohci_clk),
CLKDEV_CON_ID("pioA", &pioA_clk),
static struct platform_device at91sam9263_twi_device = {
.name = "i2c-gpio",
- .id = -1,
+ .id = 0,
.dev.platform_data = &pdata,
};
static struct platform_device at91sam9263_twi_device = {
.name = "i2c-at91sam9260",
- .id = -1,
+ .id = 0,
.resource = twi_resources,
.num_resources = ARRAY_SIZE(twi_resources),
};
static struct platform_device at91sam9rl_twi_device = {
.name = "i2c-gpio",
- .id = -1,
+ .id = 0,
.dev.platform_data = &pdata,
};
static struct platform_device at91sam9rl_twi_device = {
.name = "i2c-at91sam9g20",
- .id = -1,
+ .id = 0,
.resource = twi_resources,
.num_resources = ARRAY_SIZE(twi_resources),
};
if (!priority)
priority = at91x40_default_irq_priority;
- at91_aic_init(priority);
+ at91_aic_init(priority, at91_extern_irq);
}
.max_speed_hz = 125000 * 16,
.bus_num = 0,
.platform_data = &ads_info,
- .irq = AT91SAM9263_ID_IRQ1,
+ .irq = NR_IRQS_LEGACY + AT91SAM9263_ID_IRQ1,
},
#endif
};
.max_speed_hz = 125000 * 26, /* (max sample rate @ 3V) * (cmd + data + overhead) */
.bus_num = 0,
.platform_data = &ads_info,
- .irq = AT91SAM9261_ID_IRQ0,
+ .irq = NR_IRQS_LEGACY + AT91SAM9261_ID_IRQ0,
.controller_data = (void *) AT91_PIN_PA28, /* CS pin */
},
#endif
.max_speed_hz = 125000 * 26, /* (max sample rate @ 3V) * (cmd + data + overhead) */
.bus_num = 0,
.platform_data = &ads_info,
- .irq = AT91SAM9263_ID_IRQ1,
+ .irq = NR_IRQS_LEGACY + AT91SAM9263_ID_IRQ1,
},
#endif
};
extern void __init at91_init_irq_default(void);
extern void __init at91_init_interrupts(unsigned int priority[]);
extern void __init at91x40_init_interrupts(unsigned int priority[]);
-extern void __init at91_aic_init(unsigned int priority[]);
+extern void __init at91_aic_init(unsigned int priority[],
+ unsigned int ext_irq_mask);
extern int __init at91_aic_of_init(struct device_node *node,
struct device_node *parent);
extern int __init at91_aic5_of_init(struct device_node *node,
/*
* Initialize the AIC interrupt controller.
*/
-void __init at91_aic_init(unsigned int *priority)
+void __init at91_aic_init(unsigned int *priority, unsigned int ext_irq_mask)
{
unsigned int i;
int irq_base;
- if (at91_aic_pm_init())
+ at91_extern_irq = kzalloc(BITS_TO_LONGS(n_irqs)
+ * sizeof(*at91_extern_irq), GFP_KERNEL);
+
+ if (at91_aic_pm_init() || at91_extern_irq == NULL)
panic("Unable to allocate bit maps\n");
+ *at91_extern_irq = ext_irq_mask;
+
at91_aic_base = ioremap(AT91_AIC, 512);
if (!at91_aic_base)
panic("Unable to ioremap AIC registers\n");
void __init at91_init_interrupts(unsigned int *priority)
{
/* Initialize the AIC interrupt controller */
- at91_aic_init(priority);
+ at91_aic_init(priority, at91_extern_irq);
/* Enable GPIO interrupts */
at91_gpio_irq_setup();
}
/* at91sam9g10 */
- if ((cidr & ~AT91_CIDR_EXT) == ARCH_ID_AT91SAM9G10) {
+ if ((socid & ~AT91_CIDR_EXT) == ARCH_ID_AT91SAM9G10) {
at91_soc_initdata.type = AT91_SOC_SAM9G10;
at91_boot_soc = at91sam9261_soc;
}
#include <plat/fimc-core.h>
#include <plat/iic-core.h>
#include <plat/tv-core.h>
+#include <plat/spi-core.h>
#include <plat/regs-serial.h>
#include "common.h"
s5p_fb_setname(0, "exynos4-fb");
s5p_hdmi_setname("exynos4-hdmi");
+
+ s3c64xx_spi_setname("exynos4210-spi");
}
static void __init exynos5_map_io(void)
s3c_i2c0_setname("s3c2440-i2c");
s3c_i2c1_setname("s3c2440-i2c");
s3c_i2c2_setname("s3c2440-i2c");
+
+ s3c64xx_spi_setname("exynos4210-spi");
}
static void __init exynos4_init_clocks(int xtal)
DT_MACHINE_START(EXYNOS4210_DT, "Samsung Exynos4 (Flattened Device Tree)")
/* Maintainer: Thomas Abraham <thomas.abraham@linaro.org> */
+ .smp = smp_ops(exynos_smp_ops),
.init_irq = exynos4_init_irq,
.map_io = exynos4_dt_map_io,
.handle_irq = gic_handle_irq,
busy->div.hw.init = &init;
clk = clk_register(NULL, &busy->div.hw);
- if (!clk)
+ if (IS_ERR(clk))
kfree(busy);
return clk;
clk[esdhc2_ipg_per] = imx_clk_gate("esdhc2_ipg_per", "per4", ccm(CCM_CGCR0), 4);
clk[gpt_ipg_per] = imx_clk_gate("gpt_ipg_per", "per5", ccm(CCM_CGCR0), 5);
clk[i2c_ipg_per] = imx_clk_gate("i2c_ipg_per", "per6", ccm(CCM_CGCR0), 6);
- clk[lcdc_ipg_per] = imx_clk_gate("lcdc_ipg_per", "per8", ccm(CCM_CGCR0), 7);
- clk[nfc_ipg_per] = imx_clk_gate("nfc_ipg_per", "ipg_per", ccm(CCM_CGCR0), 8);
+ clk[lcdc_ipg_per] = imx_clk_gate("lcdc_ipg_per", "per7", ccm(CCM_CGCR0), 7);
+ clk[nfc_ipg_per] = imx_clk_gate("nfc_ipg_per", "per8", ccm(CCM_CGCR0), 8);
clk[ssi1_ipg_per] = imx_clk_gate("ssi1_ipg_per", "per13", ccm(CCM_CGCR0), 13);
clk[ssi2_ipg_per] = imx_clk_gate("ssi2_ipg_per", "per14", ccm(CCM_CGCR0), 14);
clk[uart_ipg_per] = imx_clk_gate("uart_ipg_per", "per15", ccm(CCM_CGCR0), 15);
clk[per3_div] = imx_clk_divider("per3_div", "mpll_main2", CCM_PCDR1, 16, 6);
clk[per4_div] = imx_clk_divider("per4_div", "mpll_main2", CCM_PCDR1, 24, 6);
clk[vpu_sel] = imx_clk_mux("vpu_sel", CCM_CSCR, 21, 1, vpu_sel_clks, ARRAY_SIZE(vpu_sel_clks));
- clk[vpu_div] = imx_clk_divider("vpu_div", "vpu_sel", CCM_PCDR0, 10, 3);
+ clk[vpu_div] = imx_clk_divider("vpu_div", "vpu_sel", CCM_PCDR0, 10, 6);
clk[usb_div] = imx_clk_divider("usb_div", "spll", CCM_CSCR, 28, 3);
clk[cpu_sel] = imx_clk_mux("cpu_sel", CCM_CSCR, 15, 1, cpu_sel_clks, ARRAY_SIZE(cpu_sel_clks));
clk[clko_sel] = imx_clk_mux("clko_sel", CCM_CCSR, 0, 5, clko_sel_clks, ARRAY_SIZE(clko_sel_clks));
clk[ssi1_sel] = imx_clk_mux("ssi1_sel", CCM_CSCR, 22, 1, ssi_sel_clks, ARRAY_SIZE(ssi_sel_clks));
clk[ssi2_sel] = imx_clk_mux("ssi2_sel", CCM_CSCR, 23, 1, ssi_sel_clks, ARRAY_SIZE(ssi_sel_clks));
clk[ssi1_div] = imx_clk_divider("ssi1_div", "ssi1_sel", CCM_PCDR0, 16, 6);
- clk[ssi2_div] = imx_clk_divider("ssi2_div", "ssi2_sel", CCM_PCDR0, 26, 3);
+ clk[ssi2_div] = imx_clk_divider("ssi2_div", "ssi2_sel", CCM_PCDR0, 26, 6);
clk[clko_en] = imx_clk_gate("clko_en", "clko_div", CCM_PCCR0, 0);
clk[ssi2_ipg_gate] = imx_clk_gate("ssi2_ipg_gate", "ipg", CCM_PCCR0, 0);
clk[ssi1_ipg_gate] = imx_clk_gate("ssi1_ipg_gate", "ipg", CCM_PCCR0, 1);
}
l2x0_base = ioremap(MX3x_L2CC_BASE_ADDR, 4096);
- if (IS_ERR(l2x0_base)) {
- printk(KERN_ERR "remapping L2 cache area failed with %ld\n",
- PTR_ERR(l2x0_base));
+ if (!l2x0_base) {
+ printk(KERN_ERR "remapping L2 cache area failed\n");
return;
}
select I2C_OMAP
select MENELAUS if ARCH_OMAP2
select NEON if ARCH_OMAP3 || ARCH_OMAP4 || SOC_OMAP5
- select PINCTRL
select PM_RUNTIME
select REGULATOR
select SERIAL_OMAP
#include <linux/input.h>
#include <linux/gpio_keys.h>
#include <linux/opp.h>
+#include <linux/cpu.h>
#include <linux/mtd/mtd.h>
#include <linux/mtd/partitions.h>
};
#endif
-static void __init beagle_opp_init(void)
+static int __init beagle_opp_init(void)
{
int r = 0;
- /* Initialize the omap3 opp table */
- if (omap3_opp_init()) {
+ if (!machine_is_omap3_beagle())
+ return 0;
+
+ /* Initialize the omap3 opp table if not already created. */
+ r = omap3_opp_init();
+ if (IS_ERR_VALUE(r) && (r != -EEXIST)) {
pr_err("%s: opp default init failed\n", __func__);
- return;
+ return r;
}
/* Custom OPP enabled for all xM versions */
if (cpu_is_omap3630()) {
struct device *mpu_dev, *iva_dev;
- mpu_dev = omap_device_get_by_hwmod_name("mpu");
+ mpu_dev = get_cpu_device(0);
iva_dev = omap_device_get_by_hwmod_name("iva");
if (IS_ERR(mpu_dev) || IS_ERR(iva_dev)) {
pr_err("%s: Aiee.. no mpu/dsp devices? %p %p\n",
__func__, mpu_dev, iva_dev);
- return;
+ return -ENODEV;
}
/* Enable MPU 1GHz and lower opps */
r = opp_enable(mpu_dev, 800000000);
opp_disable(iva_dev, 660000000);
}
}
- return;
+ return 0;
}
+device_initcall(beagle_opp_init);
static void __init omap3_beagle_init(void)
{
/* Ensure SDRC pins are mux'd for self-refresh */
omap_mux_init_signal("sdrc_cke0", OMAP_PIN_OUTPUT);
omap_mux_init_signal("sdrc_cke1", OMAP_PIN_OUTPUT);
-
- beagle_opp_init();
}
MACHINE_START(OMAP3_BEAGLE, "OMAP3 Beagle Board")
CLK(NULL, "gfx_fck_div_ck", &gfx_fck_div_ck, CK_AM33XX),
CLK(NULL, "sysclkout_pre_ck", &sysclkout_pre_ck, CK_AM33XX),
CLK(NULL, "clkout2_ck", &clkout2_ck, CK_AM33XX),
+ CLK(NULL, "timer_32k_ck", &clkdiv32k_ick, CK_AM33XX),
+ CLK(NULL, "timer_sys_ck", &sys_clkin_ck, CK_AM33XX),
};
int __init am33xx_clk_init(void)
"sys_off_mode", NULL, NULL, NULL,
"gpio_9", NULL, NULL, "safe_mode"),
_OMAP3_MUXENTRY(UART1_CTS, 150,
- "uart1_cts", NULL, NULL, NULL,
+ "uart1_cts", "ssi1_rdy_tx", NULL, NULL,
"gpio_150", "hsusb3_tll_clk", NULL, "safe_mode"),
_OMAP3_MUXENTRY(UART1_RTS, 149,
- "uart1_rts", NULL, NULL, NULL,
+ "uart1_rts", "ssi1_flag_tx", NULL, NULL,
"gpio_149", NULL, NULL, "safe_mode"),
_OMAP3_MUXENTRY(UART1_RX, 151,
- "uart1_rx", NULL, "mcbsp1_clkr", "mcspi4_clk",
+ "uart1_rx", "ss1_wake_tx", "mcbsp1_clkr", "mcspi4_clk",
"gpio_151", NULL, NULL, "safe_mode"),
_OMAP3_MUXENTRY(UART1_TX, 148,
- "uart1_tx", NULL, NULL, NULL,
+ "uart1_tx", "ssi1_dat_tx", NULL, NULL,
"gpio_148", NULL, NULL, "safe_mode"),
_OMAP3_MUXENTRY(UART2_CTS, 144,
"uart2_cts", "mcbsp3_dx", "gpt9_pwm_evt", NULL,
#define PM_RTA_ERRATUM_i608 (1 << 0)
#define PM_SDRC_WAKEUP_ERRATUM_i583 (1 << 1)
+#define PM_PER_MEMORIES_ERRATUM_i582 (1 << 2)
#if defined(CONFIG_PM) && defined(CONFIG_ARCH_OMAP3)
extern u16 pm34xx_errata;
/* Enable the l2 cache toggling in sleep logic */
enable_omap3630_toggle_l2_on_restore();
if (omap_rev() < OMAP3630_REV_ES1_2)
- pm34xx_errata |= PM_SDRC_WAKEUP_ERRATUM_i583;
+ pm34xx_errata |= (PM_SDRC_WAKEUP_ERRATUM_i583 |
+ PM_PER_MEMORIES_ERRATUM_i582);
+ } else if (cpu_is_omap34xx()) {
+ pm34xx_errata |= PM_PER_MEMORIES_ERRATUM_i582;
}
}
int __init omap3_pm_init(void)
{
struct power_state *pwrst, *tmp;
- struct clockdomain *neon_clkdm, *mpu_clkdm;
+ struct clockdomain *neon_clkdm, *mpu_clkdm, *per_clkdm, *wkup_clkdm;
int ret;
if (!omap3_has_io_chain_ctrl())
neon_clkdm = clkdm_lookup("neon_clkdm");
mpu_clkdm = clkdm_lookup("mpu_clkdm");
+ per_clkdm = clkdm_lookup("per_clkdm");
+ wkup_clkdm = clkdm_lookup("wkup_clkdm");
#ifdef CONFIG_SUSPEND
omap_pm_suspend = omap3_pm_suspend;
if (IS_PM34XX_ERRATUM(PM_RTA_ERRATUM_i608))
omap3630_ctrl_disable_rta();
+ /*
+ * The UART3/4 FIFO and the sidetone memory in McBSP2/3 are
+ * not correctly reset when the PER powerdomain comes back
+ * from OFF or OSWR when the CORE powerdomain is kept active.
+ * See OMAP36xx Erratum i582 "PER Domain reset issue after
+ * Domain-OFF/OSWR Wakeup". This wakeup dependency is not a
+ * complete workaround. The kernel must also prevent the PER
+ * powerdomain from going to OSWR/OFF while the CORE
+ * powerdomain is not going to OSWR/OFF. And if PER last
+ * power state was off while CORE last power state was ON, the
+ * UART3/4 and McBSP2/3 SIDETONE devices need to run a
+ * self-test using their loopback tests; if that fails, those
+ * devices are unusable until the PER/CORE can complete a transition
+ * from ON to OSWR/OFF and then back to ON.
+ *
+ * XXX Technically this workaround is only needed if off-mode
+ * or OSWR is enabled.
+ */
+ if (IS_PM34XX_ERRATUM(PM_PER_MEMORIES_ERRATUM_i582))
+ clkdm_add_wkdep(per_clkdm, wkup_clkdm);
+
clkdm_add_wkdep(neon_clkdm, mpu_clkdm);
if (omap_type() != OMAP2_DEVICE_TYPE_GP) {
omap3_secure_ram_storage =
oh->mux = omap_hwmod_mux_init(bdata->pads, bdata->pads_cnt);
+ if (console_uart_id == bdata->id) {
+ omap_device_enable(pdev);
+ pm_runtime_set_active(&pdev->dev);
+ }
+
oh->dev_attr = uart;
if (((cpu_is_omap34xx() || cpu_is_omap44xx()) && bdata->pads)
#include <plat/nand-core.h>
#include <plat/adc-core.h>
#include <plat/rtc-core.h>
+#include <plat/spi-core.h>
static struct map_desc s3c2416_iodesc[] __initdata = {
IODESC_ENT(WATCHDOG),
/* initialize device information early */
s3c2416_default_sdhci0();
s3c2416_default_sdhci1();
+ s3c64xx_spi_setname("s3c2443-spi");
iotable_init(s3c2416_iodesc, ARRAY_SIZE(s3c2416_iodesc));
}
#include <plat/nand-core.h>
#include <plat/adc-core.h>
#include <plat/rtc-core.h>
+#include <plat/spi-core.h>
static struct map_desc s3c2443_iodesc[] __initdata = {
IODESC_ENT(WATCHDOG),
s3c24xx_gpiocfg_default.set_pull = s3c2443_gpio_setpull;
s3c24xx_gpiocfg_default.get_pull = s3c2443_gpio_getpull;
+ /* initialize device information early */
+ s3c64xx_spi_setname("s3c2443-spi");
+
iotable_init(s3c2443_iodesc, ARRAY_SIZE(s3c2443_iodesc));
}
#include <plat/sdhci.h>
#include <plat/adc-core.h>
#include <plat/fb-core.h>
+#include <plat/spi-core.h>
#include <plat/gpio-cfg.h>
#include <plat/regs-irqtype.h>
#include <plat/regs-serial.h>
/* initialize any device information early */
s3c_adc_setname("s3c64xx-adc");
s3c_fb_setname("s5p64x0-fb");
+ s3c64xx_spi_setname("s5p64x0-spi");
s5p64x0_default_sdhci0();
s5p64x0_default_sdhci1();
/* initialize any device information early */
s3c_adc_setname("s3c64xx-adc");
s3c_fb_setname("s5p64x0-fb");
+ s3c64xx_spi_setname("s5p64x0-spi");
s5p64x0_default_sdhci0();
s5p64x0_default_sdhci1();
#include <plat/fb-core.h>
#include <plat/iic-core.h>
#include <plat/onenand-core.h>
+#include <plat/spi-core.h>
#include <plat/regs-serial.h>
#include <plat/watchdog-reset.h>
s3c_onenand_setname("s5pc100-onenand");
s3c_fb_setname("s5pc100-fb");
s3c_cfcon_setname("s5pc100-pata");
+
+ s3c64xx_spi_setname("s5pc100-spi");
}
void __init s5pc100_init_clocks(int xtal)
#include <plat/iic-core.h>
#include <plat/keypad-core.h>
#include <plat/tv-core.h>
+#include <plat/spi-core.h>
#include <plat/regs-serial.h>
#include "common.h"
/* setup TV devices */
s5p_hdmi_setname("s5pv210-hdmi");
+
+ s3c64xx_spi_setname("s5pv210-spi");
}
void __init s5pv210_init_clocks(int xtal)
{
#ifdef CONFIG_CACHE_L2X0
/* Early BRESP enable, Shared attribute override enable, 64K*16way */
- l2x0_init((void __iomem __force *)(0xf0100000), 0x40470000, 0x82000fff);
+ l2x0_init(IOMEM(0xf0100000), 0x40470000, 0x82000fff);
#endif
r8a7779_pm_init();
#include <linux/stat.h>
#include <linux/of.h>
#include <linux/of_irq.h>
+#include <linux/irq.h>
#include <linux/platform_data/clk-ux500.h>
#include <asm/hardware/gic.h>
if (thumb2_32b) {
offset.un = 0;
handler = do_alignment_t32_to_handler(&instr, regs, &offset);
- } else
+ } else {
+ offset.un = 0;
handler = do_alignment_ldmstm;
+ }
break;
default:
gfp_t gfp, pgprot_t prot, bool is_coherent, const void *caller)
{
u64 mask = get_coherent_dma_mask(dev);
- struct page *page;
+ struct page *page = NULL;
void *addr;
#ifdef CONFIG_DMA_API_DEBUG
struct list_head vm_list;
unsigned long vm_start;
unsigned long vm_end;
- void *priv;
int vm_active;
const void *caller;
};
struct resource res[] = {
{
.start = data->iobase,
- .end = data->iobase + SZ_4K - 1,
+ .end = data->iobase + data->iosize - 1,
.flags = IORESOURCE_MEM,
}, {
.start = data->irq,
select CLKDEV_LOOKUP
select GENERIC_IRQ_CHIP
select OMAP_DM_TIMER
+ select PINCTRL
select PROC_DEVICETREE if PROC_FS
select SPARSE_IRQ
select USE_OF
#define OMAP_UART_WER_MOD_WKUP 0X7F
/* Enable XON/XOFF flow control on output */
-#define OMAP_UART_SW_TX 0x8
+#define OMAP_UART_SW_TX 0x04
/* Enable XON/XOFF flow control on input */
-#define OMAP_UART_SW_RX 0x2
+#define OMAP_UART_SW_RX 0x04
#define OMAP_UART_SYSC_RESET 0X07
#define OMAP_UART_TCR_TRIG 0X0F
--- /dev/null
+/*
+ * Copyright (C) 2012 Heiko Stuebner <heiko@sntech.de>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#ifndef __PLAT_S3C_SPI_CORE_H
+#define __PLAT_S3C_SPI_CORE_H
+
+/* These functions are only for use with the core support code, such as
+ * the cpu specific initialisation code
+ */
+
+/* re-define device name depending on support. */
+static inline void s3c64xx_spi_setname(char *name)
+{
+#ifdef CONFIG_S3C64XX_DEV_SPI0
+ s3c64xx_device_spi0.name = name;
+#endif
+#ifdef CONFIG_S3C64XX_DEV_SPI1
+ s3c64xx_device_spi1.name = name;
+#endif
+#ifdef CONFIG_S3C64XX_DEV_SPI2
+ s3c64xx_device_spi2.name = name;
+#endif
+}
+
+#endif /* __PLAT_S3C_SPI_CORE_H */
#
include/generated/mach-types.h: $(src)/gen-mach-types $(src)/mach-types
- @echo ' Generating $@'
+ $(kecho) ' Generating $@'
@mkdir -p $(dir $@)
$(Q)$(AWK) -f $^ > $@ || { rm -f $@; /bin/false; }
#include <xen/page.h>
#include <xen/grant_table.h>
-int arch_gnttab_map_shared(unsigned long *frames, unsigned long nr_gframes,
+int arch_gnttab_map_shared(xen_pfn_t *frames, unsigned long nr_gframes,
unsigned long max_nr_gframes,
void **__shared)
{
#include <linux/linkage.h>
#include <asm/assembler.h>
+#include <asm/opcodes-virt.h>
#include <xen/interface/xen.h>
-/* HVC 0xEA1 */
-#ifdef CONFIG_THUMB2_KERNEL
-#define xen_hvc .word 0xf7e08ea1
-#else
-#define xen_hvc .word 0xe140ea71
-#endif
+#define XEN_IMM 0xEA1
#define HYPERCALL_SIMPLE(hypercall) \
ENTRY(HYPERVISOR_##hypercall) \
mov r12, #__HYPERVISOR_##hypercall; \
- xen_hvc; \
+ __HVC(XEN_IMM); \
mov pc, lr; \
ENDPROC(HYPERVISOR_##hypercall)
stmdb sp!, {r4} \
ldr r4, [sp, #4] \
mov r12, #__HYPERVISOR_##hypercall; \
- xen_hvc \
+ __HVC(XEN_IMM); \
ldm sp!, {r4} \
mov pc, lr \
ENDPROC(HYPERVISOR_##hypercall)
mov r2, r3
ldr r3, [sp, #8]
ldr r4, [sp, #4]
- xen_hvc
+ __HVC(XEN_IMM)
ldm sp!, {r4}
mov pc, lr
ENDPROC(privcmd_call);
select GENERIC_CPU_DEVICES
select ARCH_WANT_IPC_PARSE_VERSION
select GENERIC_KERNEL_THREAD
+ select GENERIC_KERNEL_EXECVE
config ZONE_DMA
bool
INITRD_PHYS = 0x02180000
INITRD_VIRT = 0x02180000
+OBJCOPYFLAGS :=-O binary -R .note -R .note.gnu.build-id -R .comment
+
#
# If you don't define ZRELADDR above,
# then it defaults to ZTEXTADDR
targets: $(obj)/Image
$(obj)/Image: vmlinux FORCE
- $(OBJCOPY) -O binary -R .note -R .comment -S vmlinux $@
+ $(OBJCOPY) $(OBJCOPYFLAGS) -S vmlinux $@
#$(obj)/Image: $(CONFIGURE) $(SYSTEM)
-# $(OBJCOPY) -O binary -R .note -R .comment -g -S $(SYSTEM) $@
+# $(OBJCOPY) $(OBJCOPYFLAGS) -g -S $(SYSTEM) $@
bzImage: zImage
zImage: $(CONFIGURE) compressed/$(LINUX)
- $(OBJCOPY) -O binary -R .note -R .comment -S compressed/$(LINUX) $@
+ $(OBJCOPY) $(OBJCOPYFLAGS) -S compressed/$(LINUX) $@
bootpImage: bootp/bootp
- $(OBJCOPY) -O binary -R .note -R .comment -S bootp/bootp $@
+ $(OBJCOPY) $(OBJCOPYFLAGS) -S bootp/bootp $@
compressed/$(LINUX): $(LINUX) dep
@$(MAKE) -C compressed $(LINUX)
#define __ARCH_WANT_SYS_RT_SIGACTION
#define __ARCH_WANT_SYS_RT_SIGSUSPEND
#define __ARCH_WANT_SYS_EXECVE
-#define __ARCH_WANT_KERNEL_EXECVE
/*
* "Conditional" syscalls
call schedule_tail
calll.p @(gr21,gr0)
or gr20,gr20,gr8
- bra sys_exit
-
- .globl ret_from_kernel_execve
-ret_from_kernel_execve:
- ori gr28,0,sp
bra __syscall_exit
###################################################################################################
subicc gr5,#0,gr0,icc0
beq icc0,#0,__entry_return_direct
-__entry_preempt_need_resched:
- ldi @(gr15,#TI_FLAGS),gr4
- andicc gr4,#_TIF_NEED_RESCHED,gr0,icc0
- beq icc0,#1,__entry_return_direct
-
- setlos #PREEMPT_ACTIVE,gr5
- sti gr5,@(gr15,#TI_FLAGS)
-
- andi gr23,#~PSR_PIL,gr23
- movgs gr23,psr
-
- call schedule
- sti gr0,@(gr15,#TI_PRE_COUNT)
-
- movsg psr,gr23
- ori gr23,#PSR_PIL_14,gr23
- movgs gr23,psr
- bra __entry_preempt_need_resched
-#else
- bra __entry_return_direct
+ subcc gr0,gr0,gr0,icc2 /* set Z and clear C */
+ call preempt_schedule_irq
#endif
+ bra __entry_return_direct
###############################################################################
childregs = (struct pt_regs *)
(task_stack_page(p) + THREAD_SIZE - FRV_FRAME0_SIZE);
+ /* set up the userspace frame (the only place that the USP is stored) */
+ *childregs = *__kernel_frame0_ptr;
+
p->set_child_tid = p->clear_child_tid = NULL;
p->thread.frame = childregs;
p->thread.frame0 = childregs;
if (unlikely(!regs)) {
- memset(childregs, 0, sizeof(struct pt_regs));
childregs->gr9 = usp; /* function */
childregs->gr8 = arg;
- childregs->psr = PSR_S;
p->thread.pc = (unsigned long) ret_from_kernel_thread;
save_user_regs(p->thread.user);
return 0;
#include <linux/types.h>
#include <linux/slab.h>
+#include <linux/export.h>
#include <linux/dma-mapping.h>
#include <linux/list.h>
#include <linux/pci.h>
generic-y += clkdev.h
generic-y += exec.h
+generic-y += kvm_para.h
+++ /dev/null
-/*
- * Copyright (C) 2007 Xiantao Zhang <xiantao.zhang@intel.com>
- *
- * This program is free software; you can redistribute it and/or modify it
- * under the terms and conditions of the GNU General Public License,
- * version 2, as published by the Free Software Foundation.
- *
- * This program is distributed in the hope it will be useful, but WITHOUT
- * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
- * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
- * more details.
- *
- * You should have received a copy of the GNU General Public License along with
- * this program; if not, write to the Free Software Foundation, Inc., 59 Temple
- * Place - Suite 330, Boston, MA 02111-1307 USA.
- *
- */
-#ifndef __IA64_KVM_PARA_H
-#define __IA64_KVM_PARA_H
-
-#include <uapi/asm/kvm_para.h>
-
-
-static inline unsigned int kvm_arch_para_features(void)
-{
- return 0;
-}
-
-static inline bool kvm_check_and_clear_guest_paused(void)
-{
- return false;
-}
-
-#endif
-include include/asm-generic/Kbuild.asm
-header-y += cachectl.h
generic-y += bitsperlong.h
generic-y += clkdev.h
+++ /dev/null
-#ifndef __M68K_A_OUT_H__
-#define __M68K_A_OUT_H__
-
-struct exec
-{
- unsigned long a_info; /* Use macros N_MAGIC, etc for access */
- unsigned a_text; /* length of text, in bytes */
- unsigned a_data; /* length of data, in bytes */
- unsigned a_bss; /* length of uninitialized data area for file, in bytes */
- unsigned a_syms; /* length of symbol table data in file, in bytes */
- unsigned a_entry; /* start address */
- unsigned a_trsize; /* length of relocation info for text, in bytes */
- unsigned a_drsize; /* length of relocation info for data, in bytes */
-};
-
-#define N_TRSIZE(a) ((a).a_trsize)
-#define N_DRSIZE(a) ((a).a_drsize)
-#define N_SYMSIZE(a) ((a).a_syms)
-
-#endif /* __M68K_A_OUT_H__ */
+++ /dev/null
-#ifndef __ASMm68k_AUXVEC_H
-#define __ASMm68k_AUXVEC_H
-
-#endif
+++ /dev/null
-#ifndef _M68K_BYTEORDER_H
-#define _M68K_BYTEORDER_H
-
-#include <linux/byteorder/big_endian.h>
-
-#endif /* _M68K_BYTEORDER_H */
+++ /dev/null
-#ifndef _M68K_CACHECTL_H
-#define _M68K_CACHECTL_H
-
-/* Definitions for the cacheflush system call. */
-
-#define FLUSH_SCOPE_LINE 1 /* Flush a cache line */
-#define FLUSH_SCOPE_PAGE 2 /* Flush a page */
-#define FLUSH_SCOPE_ALL 3 /* Flush the whole cache -- superuser only */
-
-#define FLUSH_CACHE_DATA 1 /* Writeback and flush data cache */
-#define FLUSH_CACHE_INSN 2 /* Flush instruction cache */
-#define FLUSH_CACHE_BOTH 3 /* Flush both caches */
-
-#endif /* _M68K_CACHECTL_H */
+++ /dev/null
-#ifndef _M68K_FCNTL_H
-#define _M68K_FCNTL_H
-
-#define O_DIRECTORY 040000 /* must be a directory */
-#define O_NOFOLLOW 0100000 /* don't follow links */
-#define O_DIRECT 0200000 /* direct disk access hint - currently ignored */
-#define O_LARGEFILE 0400000
-
-#include <asm-generic/fcntl.h>
-
-#endif /* _M68K_FCNTL_H */
+++ /dev/null
-#ifndef __ARCH_M68K_IOCTLS_H__
-#define __ARCH_M68K_IOCTLS_H__
-
-#define FIOQSIZE 0x545E
-
-#include <asm-generic/ioctls.h>
-
-#endif /* __ARCH_M68K_IOCTLS_H__ */
+++ /dev/null
-#ifndef _M68K_MSGBUF_H
-#define _M68K_MSGBUF_H
-
-/*
- * The msqid64_ds structure for m68k architecture.
- * Note extra padding because this structure is passed back and forth
- * between kernel and user space.
- *
- * Pad space is left for:
- * - 64-bit time_t to solve y2038 problem
- * - 2 miscellaneous 32-bit values
- */
-
-struct msqid64_ds {
- struct ipc64_perm msg_perm;
- __kernel_time_t msg_stime; /* last msgsnd time */
- unsigned long __unused1;
- __kernel_time_t msg_rtime; /* last msgrcv time */
- unsigned long __unused2;
- __kernel_time_t msg_ctime; /* last change time */
- unsigned long __unused3;
- unsigned long msg_cbytes; /* current number of bytes on queue */
- unsigned long msg_qnum; /* number of messages in queue */
- unsigned long msg_qbytes; /* max number of bytes on queue */
- __kernel_pid_t msg_lspid; /* pid of last msgsnd */
- __kernel_pid_t msg_lrpid; /* last receive pid */
- unsigned long __unused4;
- unsigned long __unused5;
-};
-
-#endif /* _M68K_MSGBUF_H */
+++ /dev/null
-#ifndef _M68K_PARAM_H
-#define _M68K_PARAM_H
-
-#ifdef __uClinux__
-#define EXEC_PAGESIZE 4096
-#else
-#define EXEC_PAGESIZE 8192
-#endif
-
-#include <asm-generic/param.h>
-
-#endif /* _M68K_PARAM_H */
+++ /dev/null
-#ifndef __m68k_POLL_H
-#define __m68k_POLL_H
-
-#define POLLWRNORM POLLOUT
-#define POLLWRBAND 256
-
-#include <asm-generic/poll.h>
-
-#endif
+++ /dev/null
-#ifndef __ARCH_M68K_POSIX_TYPES_H
-#define __ARCH_M68K_POSIX_TYPES_H
-
-/*
- * This file is generally used by user-level software, so you need to
- * be a little careful about namespace pollution etc. Also, we cannot
- * assume GCC is being used.
- */
-
-typedef unsigned short __kernel_mode_t;
-#define __kernel_mode_t __kernel_mode_t
-
-typedef unsigned short __kernel_ipc_pid_t;
-#define __kernel_ipc_pid_t __kernel_ipc_pid_t
-
-typedef unsigned short __kernel_uid_t;
-typedef unsigned short __kernel_gid_t;
-#define __kernel_uid_t __kernel_uid_t
-
-typedef unsigned short __kernel_old_dev_t;
-#define __kernel_old_dev_t __kernel_old_dev_t
-
-#include <asm-generic/posix_types.h>
-
-#endif
#ifndef _M68K_PTRACE_H
#define _M68K_PTRACE_H
-#define PT_D1 0
-#define PT_D2 1
-#define PT_D3 2
-#define PT_D4 3
-#define PT_D5 4
-#define PT_D6 5
-#define PT_D7 6
-#define PT_A0 7
-#define PT_A1 8
-#define PT_A2 9
-#define PT_A3 10
-#define PT_A4 11
-#define PT_A5 12
-#define PT_A6 13
-#define PT_D0 14
-#define PT_USP 15
-#define PT_ORIG_D0 16
-#define PT_SR 17
-#define PT_PC 18
+#include <uapi/asm/ptrace.h>
#ifndef __ASSEMBLY__
-/* this struct defines the way the registers are stored on the
- stack during a system call. */
-
-struct pt_regs {
- long d1;
- long d2;
- long d3;
- long d4;
- long d5;
- long a0;
- long a1;
- long a2;
- long d0;
- long orig_d0;
- long stkadj;
-#ifdef CONFIG_COLDFIRE
- unsigned format : 4; /* frame format specifier */
- unsigned vector : 12; /* vector offset */
- unsigned short sr;
- unsigned long pc;
-#else
- unsigned short sr;
- unsigned long pc;
- unsigned format : 4; /* frame format specifier */
- unsigned vector : 12; /* vector offset */
-#endif
-};
-
-/*
- * This is the extended stack used by signal handlers and the context
- * switcher: it's pushed after the normal "struct pt_regs".
- */
-struct switch_stack {
- unsigned long d6;
- unsigned long d7;
- unsigned long a3;
- unsigned long a4;
- unsigned long a5;
- unsigned long a6;
- unsigned long retpc;
-};
-
-/* Arbitrarily choose the same ptrace numbers as used by the Sparc code. */
-#define PTRACE_GETREGS 12
-#define PTRACE_SETREGS 13
-#define PTRACE_GETFPREGS 14
-#define PTRACE_SETFPREGS 15
-
-#define PTRACE_GET_THREAD_AREA 25
-
-#define PTRACE_SINGLEBLOCK 33 /* resume execution until next branch */
-
-#ifdef __KERNEL__
-
#ifndef PS_S
#define PS_S (0x2000)
#define PS_M (0x1000)
#define arch_has_block_step() (1)
#endif
-#endif /* __KERNEL__ */
#endif /* __ASSEMBLY__ */
#endif /* _M68K_PTRACE_H */
+++ /dev/null
-#ifndef _M68K_SEMBUF_H
-#define _M68K_SEMBUF_H
-
-/*
- * The semid64_ds structure for m68k architecture.
- * Note extra padding because this structure is passed back and forth
- * between kernel and user space.
- *
- * Pad space is left for:
- * - 64-bit time_t to solve y2038 problem
- * - 2 miscellaneous 32-bit values
- */
-
-struct semid64_ds {
- struct ipc64_perm sem_perm; /* permissions .. see ipc.h */
- __kernel_time_t sem_otime; /* last semop time */
- unsigned long __unused1;
- __kernel_time_t sem_ctime; /* last change time */
- unsigned long __unused2;
- unsigned long sem_nsems; /* no. of semaphores in array */
- unsigned long __unused3;
- unsigned long __unused4;
-};
-
-#endif /* _M68K_SEMBUF_H */
** Redesign of the boot information structure; moved boot information
** structure to bootinfo.h
*/
-
#ifndef _M68K_SETUP_H
#define _M68K_SETUP_H
+#include <uapi/asm/setup.h>
- /*
- * Linux/m68k Architectures
- */
-
-#define MACH_AMIGA 1
-#define MACH_ATARI 2
-#define MACH_MAC 3
-#define MACH_APOLLO 4
-#define MACH_SUN3 5
-#define MACH_MVME147 6
-#define MACH_MVME16x 7
-#define MACH_BVME6000 8
-#define MACH_HP300 9
-#define MACH_Q40 10
-#define MACH_SUN3X 11
-#define MACH_M54XX 12
-
-#define COMMAND_LINE_SIZE 256
-
-#ifdef __KERNEL__
-
#define CL_SIZE COMMAND_LINE_SIZE
#ifndef __ASSEMBLY__
# define MACH_TYPE (m68k_machtype)
#endif
-#endif /* __KERNEL__ */
-
-
- /*
- * CPU, FPU and MMU types
- *
- * Note: we may rely on the following equalities:
- *
- * CPU_68020 == MMU_68851
- * CPU_68030 == MMU_68030
- * CPU_68040 == FPU_68040 == MMU_68040
- * CPU_68060 == FPU_68060 == MMU_68060
- */
-
-#define CPUB_68020 0
-#define CPUB_68030 1
-#define CPUB_68040 2
-#define CPUB_68060 3
-#define CPUB_COLDFIRE 4
-
-#define CPU_68020 (1<<CPUB_68020)
-#define CPU_68030 (1<<CPUB_68030)
-#define CPU_68040 (1<<CPUB_68040)
-#define CPU_68060 (1<<CPUB_68060)
-#define CPU_COLDFIRE (1<<CPUB_COLDFIRE)
-
-#define FPUB_68881 0
-#define FPUB_68882 1
-#define FPUB_68040 2 /* Internal FPU */
-#define FPUB_68060 3 /* Internal FPU */
-#define FPUB_SUNFPA 4 /* Sun-3 FPA */
-#define FPUB_COLDFIRE 5 /* ColdFire FPU */
-
-#define FPU_68881 (1<<FPUB_68881)
-#define FPU_68882 (1<<FPUB_68882)
-#define FPU_68040 (1<<FPUB_68040)
-#define FPU_68060 (1<<FPUB_68060)
-#define FPU_SUNFPA (1<<FPUB_SUNFPA)
-#define FPU_COLDFIRE (1<<FPUB_COLDFIRE)
-
-#define MMUB_68851 0
-#define MMUB_68030 1 /* Internal MMU */
-#define MMUB_68040 2 /* Internal MMU */
-#define MMUB_68060 3 /* Internal MMU */
-#define MMUB_APOLLO 4 /* Custom Apollo */
-#define MMUB_SUN3 5 /* Custom Sun-3 */
-#define MMUB_COLDFIRE 6 /* Internal MMU */
-
-#define MMU_68851 (1<<MMUB_68851)
-#define MMU_68030 (1<<MMUB_68030)
-#define MMU_68040 (1<<MMUB_68040)
-#define MMU_68060 (1<<MMUB_68060)
-#define MMU_SUN3 (1<<MMUB_SUN3)
-#define MMU_APOLLO (1<<MMUB_APOLLO)
-#define MMU_COLDFIRE (1<<MMUB_COLDFIRE)
-
-#ifdef __KERNEL__
#ifndef __ASSEMBLY__
extern unsigned long m68k_cputype;
extern struct mem_info m68k_memory[NUM_MEMINFO];/* memory description */
#endif
-#endif /* __KERNEL__ */
-
#endif /* _M68K_SETUP_H */
+++ /dev/null
-#ifndef _M68K_SHMBUF_H
-#define _M68K_SHMBUF_H
-
-/*
- * The shmid64_ds structure for m68k architecture.
- * Note extra padding because this structure is passed back and forth
- * between kernel and user space.
- *
- * Pad space is left for:
- * - 64-bit time_t to solve y2038 problem
- * - 2 miscellaneous 32-bit values
- */
-
-struct shmid64_ds {
- struct ipc64_perm shm_perm; /* operation perms */
- size_t shm_segsz; /* size of segment (bytes) */
- __kernel_time_t shm_atime; /* last attach time */
- unsigned long __unused1;
- __kernel_time_t shm_dtime; /* last detach time */
- unsigned long __unused2;
- __kernel_time_t shm_ctime; /* last change time */
- unsigned long __unused3;
- __kernel_pid_t shm_cpid; /* pid of creator */
- __kernel_pid_t shm_lpid; /* pid of last operator */
- unsigned long shm_nattch; /* no. of current attaches */
- unsigned long __unused4;
- unsigned long __unused5;
-};
-
-struct shminfo64 {
- unsigned long shmmax;
- unsigned long shmmin;
- unsigned long shmmni;
- unsigned long shmseg;
- unsigned long shmall;
- unsigned long __unused1;
- unsigned long __unused2;
- unsigned long __unused3;
- unsigned long __unused4;
-};
-
-#endif /* _M68K_SHMBUF_H */
+++ /dev/null
-#ifndef _ASM_M68k_SIGCONTEXT_H
-#define _ASM_M68k_SIGCONTEXT_H
-
-struct sigcontext {
- unsigned long sc_mask; /* old sigmask */
- unsigned long sc_usp; /* old user stack pointer */
- unsigned long sc_d0;
- unsigned long sc_d1;
- unsigned long sc_a0;
- unsigned long sc_a1;
-#ifdef __uClinux__
- unsigned long sc_a5;
-#endif
- unsigned short sc_sr;
- unsigned long sc_pc;
- unsigned short sc_formatvec;
-#ifndef __uClinux__
- unsigned long sc_fpregs[2*3]; /* room for two fp registers */
- unsigned long sc_fpcntl[3];
- unsigned char sc_fpstate[216];
-#endif
-};
-
-#endif
#ifndef _M68K_SIGNAL_H
#define _M68K_SIGNAL_H
-#include <linux/types.h>
+#include <uapi/asm/signal.h>
-/* Avoid too many header ordering problems. */
-struct siginfo;
-
-#ifdef __KERNEL__
/* Most things should be clean enough to redefine this at will, if care
is taken to make libc match. */
unsigned long sig[_NSIG_WORDS];
} sigset_t;
-#else
-/* Here we must cater to libcs that poke about in kernel headers. */
-
-#define NSIG 32
-typedef unsigned long sigset_t;
-
-#endif /* __KERNEL__ */
-
-#define SIGHUP 1
-#define SIGINT 2
-#define SIGQUIT 3
-#define SIGILL 4
-#define SIGTRAP 5
-#define SIGABRT 6
-#define SIGIOT 6
-#define SIGBUS 7
-#define SIGFPE 8
-#define SIGKILL 9
-#define SIGUSR1 10
-#define SIGSEGV 11
-#define SIGUSR2 12
-#define SIGPIPE 13
-#define SIGALRM 14
-#define SIGTERM 15
-#define SIGSTKFLT 16
-#define SIGCHLD 17
-#define SIGCONT 18
-#define SIGSTOP 19
-#define SIGTSTP 20
-#define SIGTTIN 21
-#define SIGTTOU 22
-#define SIGURG 23
-#define SIGXCPU 24
-#define SIGXFSZ 25
-#define SIGVTALRM 26
-#define SIGPROF 27
-#define SIGWINCH 28
-#define SIGIO 29
-#define SIGPOLL SIGIO
-/*
-#define SIGLOST 29
-*/
-#define SIGPWR 30
-#define SIGSYS 31
-#define SIGUNUSED 31
-
-/* These should not be considered constants from userland. */
-#define SIGRTMIN 32
-#define SIGRTMAX _NSIG
-
-/*
- * SA_FLAGS values:
- *
- * SA_ONSTACK indicates that a registered stack_t will be used.
- * SA_RESTART flag to get restarting signals (which were the default long ago)
- * SA_NOCLDSTOP flag to turn off SIGCHLD when children stop.
- * SA_RESETHAND clears the handler when the signal is delivered.
- * SA_NOCLDWAIT flag on SIGCHLD to inhibit zombies.
- * SA_NODEFER prevents the current signal from being masked in the handler.
- *
- * SA_ONESHOT and SA_NOMASK are the historical Linux names for the Single
- * Unix names RESETHAND and NODEFER respectively.
- */
-#define SA_NOCLDSTOP 0x00000001
-#define SA_NOCLDWAIT 0x00000002
-#define SA_SIGINFO 0x00000004
-#define SA_ONSTACK 0x08000000
-#define SA_RESTART 0x10000000
-#define SA_NODEFER 0x40000000
-#define SA_RESETHAND 0x80000000
-
-#define SA_NOMASK SA_NODEFER
-#define SA_ONESHOT SA_RESETHAND
-
-/*
- * sigaltstack controls
- */
-#define SS_ONSTACK 1
-#define SS_DISABLE 2
-
-#define MINSIGSTKSZ 2048
-#define SIGSTKSZ 8192
-
-#include <asm-generic/signal-defs.h>
-
-#ifdef __KERNEL__
struct old_sigaction {
__sighandler_t sa_handler;
old_sigset_t sa_mask;
struct k_sigaction {
struct sigaction sa;
};
-#else
-/* Here we must cater to libcs that poke about in kernel headers. */
-
-struct sigaction {
- union {
- __sighandler_t _sa_handler;
- void (*_sa_sigaction)(int, struct siginfo *, void *);
- } _u;
- sigset_t sa_mask;
- unsigned long sa_flags;
- void (*sa_restorer)(void);
-};
-
-#define sa_handler _u._sa_handler
-#define sa_sigaction _u._sa_sigaction
-
-#endif /* __KERNEL__ */
-
-typedef struct sigaltstack {
- void __user *ss_sp;
- int ss_flags;
- size_t ss_size;
-} stack_t;
-
-#ifdef __KERNEL__
#include <asm/sigcontext.h>
#ifndef CONFIG_CPU_HAS_NO_BITFIELDS
extern void ptrace_signal_deliver(struct pt_regs *regs, void *cookie);
#endif /* __uClinux__ */
-#endif /* __KERNEL__ */
#endif /* _M68K_SIGNAL_H */
+++ /dev/null
-#ifndef _ASM_SOCKET_H
-#define _ASM_SOCKET_H
-
-#include <asm/sockios.h>
-
-/* For setsockopt(2) */
-#define SOL_SOCKET 1
-
-#define SO_DEBUG 1
-#define SO_REUSEADDR 2
-#define SO_TYPE 3
-#define SO_ERROR 4
-#define SO_DONTROUTE 5
-#define SO_BROADCAST 6
-#define SO_SNDBUF 7
-#define SO_RCVBUF 8
-#define SO_SNDBUFFORCE 32
-#define SO_RCVBUFFORCE 33
-#define SO_KEEPALIVE 9
-#define SO_OOBINLINE 10
-#define SO_NO_CHECK 11
-#define SO_PRIORITY 12
-#define SO_LINGER 13
-#define SO_BSDCOMPAT 14
-/* To add :#define SO_REUSEPORT 15 */
-#define SO_PASSCRED 16
-#define SO_PEERCRED 17
-#define SO_RCVLOWAT 18
-#define SO_SNDLOWAT 19
-#define SO_RCVTIMEO 20
-#define SO_SNDTIMEO 21
-
-/* Security levels - as per NRL IPv6 - don't actually do anything */
-#define SO_SECURITY_AUTHENTICATION 22
-#define SO_SECURITY_ENCRYPTION_TRANSPORT 23
-#define SO_SECURITY_ENCRYPTION_NETWORK 24
-
-#define SO_BINDTODEVICE 25
-
-/* Socket filtering */
-#define SO_ATTACH_FILTER 26
-#define SO_DETACH_FILTER 27
-
-#define SO_PEERNAME 28
-#define SO_TIMESTAMP 29
-#define SCM_TIMESTAMP SO_TIMESTAMP
-
-#define SO_ACCEPTCONN 30
-
-#define SO_PEERSEC 31
-#define SO_PASSSEC 34
-#define SO_TIMESTAMPNS 35
-#define SCM_TIMESTAMPNS SO_TIMESTAMPNS
-
-#define SO_MARK 36
-
-#define SO_TIMESTAMPING 37
-#define SCM_TIMESTAMPING SO_TIMESTAMPING
-
-#define SO_PROTOCOL 38
-#define SO_DOMAIN 39
-
-#define SO_RXQ_OVFL 40
-
-#define SO_WIFI_STATUS 41
-#define SCM_WIFI_STATUS SO_WIFI_STATUS
-#define SO_PEEK_OFF 42
-
-/* Instruct lower device to use last 4-bytes of skb data as FCS */
-#define SO_NOFCS 43
-
-#endif /* _ASM_SOCKET_H */
+++ /dev/null
-#ifndef __ARCH_M68K_SOCKIOS__
-#define __ARCH_M68K_SOCKIOS__
-
-/* Socket-level I/O control calls. */
-#define FIOSETOWN 0x8901
-#define SIOCSPGRP 0x8902
-#define FIOGETOWN 0x8903
-#define SIOCGPGRP 0x8904
-#define SIOCATMARK 0x8905
-#define SIOCGSTAMP 0x8906 /* Get stamp (timeval) */
-#define SIOCGSTAMPNS 0x8907 /* Get stamp (timespec) */
-
-#endif /* __ARCH_M68K_SOCKIOS__ */
+++ /dev/null
-#ifndef _M68K_STAT_H
-#define _M68K_STAT_H
-
-struct __old_kernel_stat {
- unsigned short st_dev;
- unsigned short st_ino;
- unsigned short st_mode;
- unsigned short st_nlink;
- unsigned short st_uid;
- unsigned short st_gid;
- unsigned short st_rdev;
- unsigned long st_size;
- unsigned long st_atime;
- unsigned long st_mtime;
- unsigned long st_ctime;
-};
-
-struct stat {
- unsigned short st_dev;
- unsigned short __pad1;
- unsigned long st_ino;
- unsigned short st_mode;
- unsigned short st_nlink;
- unsigned short st_uid;
- unsigned short st_gid;
- unsigned short st_rdev;
- unsigned short __pad2;
- unsigned long st_size;
- unsigned long st_blksize;
- unsigned long st_blocks;
- unsigned long st_atime;
- unsigned long __unused1;
- unsigned long st_mtime;
- unsigned long __unused2;
- unsigned long st_ctime;
- unsigned long __unused3;
- unsigned long __unused4;
- unsigned long __unused5;
-};
-
-/* This matches struct stat64 in glibc2.1, hence the absolutely
- * insane amounts of padding around dev_t's.
- */
-struct stat64 {
- unsigned long long st_dev;
- unsigned char __pad1[2];
-
-#define STAT64_HAS_BROKEN_ST_INO 1
- unsigned long __st_ino;
-
- unsigned int st_mode;
- unsigned int st_nlink;
-
- unsigned long st_uid;
- unsigned long st_gid;
-
- unsigned long long st_rdev;
- unsigned char __pad3[2];
-
- long long st_size;
- unsigned long st_blksize;
-
- unsigned long long st_blocks; /* Number 512-byte blocks allocated. */
-
- unsigned long st_atime;
- unsigned long st_atime_nsec;
-
- unsigned long st_mtime;
- unsigned long st_mtime_nsec;
-
- unsigned long st_ctime;
- unsigned long st_ctime_nsec;
-
- unsigned long long st_ino;
-};
-
-#endif /* _M68K_STAT_H */
+++ /dev/null
-#ifndef _M68K_SWAB_H
-#define _M68K_SWAB_H
-
-#include <linux/types.h>
-#include <linux/compiler.h>
-
-#define __SWAB_64_THRU_32__
-
-#if defined (__mcfisaaplus__) || defined (__mcfisac__)
-static inline __attribute_const__ __u32 __arch_swab32(__u32 val)
-{
- __asm__("byterev %0" : "=d" (val) : "0" (val));
- return val;
-}
-
-#define __arch_swab32 __arch_swab32
-#elif !defined(__mcoldfire__)
-
-static inline __attribute_const__ __u32 __arch_swab32(__u32 val)
-{
- __asm__("rolw #8,%0; swap %0; rolw #8,%0" : "=d" (val) : "0" (val));
- return val;
-}
-#define __arch_swab32 __arch_swab32
-#endif
-
-#endif /* _M68K_SWAB_H */
+++ /dev/null
-#ifndef __ARCH_M68K_TERMBITS_H__
-#define __ARCH_M68K_TERMBITS_H__
-
-#include <linux/posix_types.h>
-
-typedef unsigned char cc_t;
-typedef unsigned int speed_t;
-typedef unsigned int tcflag_t;
-
-#define NCCS 19
-struct termios {
- tcflag_t c_iflag; /* input mode flags */
- tcflag_t c_oflag; /* output mode flags */
- tcflag_t c_cflag; /* control mode flags */
- tcflag_t c_lflag; /* local mode flags */
- cc_t c_line; /* line discipline */
- cc_t c_cc[NCCS]; /* control characters */
-};
-
-struct termios2 {
- tcflag_t c_iflag; /* input mode flags */
- tcflag_t c_oflag; /* output mode flags */
- tcflag_t c_cflag; /* control mode flags */
- tcflag_t c_lflag; /* local mode flags */
- cc_t c_line; /* line discipline */
- cc_t c_cc[NCCS]; /* control characters */
- speed_t c_ispeed; /* input speed */
- speed_t c_ospeed; /* output speed */
-};
-
-struct ktermios {
- tcflag_t c_iflag; /* input mode flags */
- tcflag_t c_oflag; /* output mode flags */
- tcflag_t c_cflag; /* control mode flags */
- tcflag_t c_lflag; /* local mode flags */
- cc_t c_line; /* line discipline */
- cc_t c_cc[NCCS]; /* control characters */
- speed_t c_ispeed; /* input speed */
- speed_t c_ospeed; /* output speed */
-};
-
-/* c_cc characters */
-#define VINTR 0
-#define VQUIT 1
-#define VERASE 2
-#define VKILL 3
-#define VEOF 4
-#define VTIME 5
-#define VMIN 6
-#define VSWTC 7
-#define VSTART 8
-#define VSTOP 9
-#define VSUSP 10
-#define VEOL 11
-#define VREPRINT 12
-#define VDISCARD 13
-#define VWERASE 14
-#define VLNEXT 15
-#define VEOL2 16
-
-
-/* c_iflag bits */
-#define IGNBRK 0000001
-#define BRKINT 0000002
-#define IGNPAR 0000004
-#define PARMRK 0000010
-#define INPCK 0000020
-#define ISTRIP 0000040
-#define INLCR 0000100
-#define IGNCR 0000200
-#define ICRNL 0000400
-#define IUCLC 0001000
-#define IXON 0002000
-#define IXANY 0004000
-#define IXOFF 0010000
-#define IMAXBEL 0020000
-#define IUTF8 0040000
-
-/* c_oflag bits */
-#define OPOST 0000001
-#define OLCUC 0000002
-#define ONLCR 0000004
-#define OCRNL 0000010
-#define ONOCR 0000020
-#define ONLRET 0000040
-#define OFILL 0000100
-#define OFDEL 0000200
-#define NLDLY 0000400
-#define NL0 0000000
-#define NL1 0000400
-#define CRDLY 0003000
-#define CR0 0000000
-#define CR1 0001000
-#define CR2 0002000
-#define CR3 0003000
-#define TABDLY 0014000
-#define TAB0 0000000
-#define TAB1 0004000
-#define TAB2 0010000
-#define TAB3 0014000
-#define XTABS 0014000
-#define BSDLY 0020000
-#define BS0 0000000
-#define BS1 0020000
-#define VTDLY 0040000
-#define VT0 0000000
-#define VT1 0040000
-#define FFDLY 0100000
-#define FF0 0000000
-#define FF1 0100000
-
-/* c_cflag bit meaning */
-#define CBAUD 0010017
-#define B0 0000000 /* hang up */
-#define B50 0000001
-#define B75 0000002
-#define B110 0000003
-#define B134 0000004
-#define B150 0000005
-#define B200 0000006
-#define B300 0000007
-#define B600 0000010
-#define B1200 0000011
-#define B1800 0000012
-#define B2400 0000013
-#define B4800 0000014
-#define B9600 0000015
-#define B19200 0000016
-#define B38400 0000017
-#define EXTA B19200
-#define EXTB B38400
-#define CSIZE 0000060
-#define CS5 0000000
-#define CS6 0000020
-#define CS7 0000040
-#define CS8 0000060
-#define CSTOPB 0000100
-#define CREAD 0000200
-#define PARENB 0000400
-#define PARODD 0001000
-#define HUPCL 0002000
-#define CLOCAL 0004000
-#define CBAUDEX 0010000
-#define BOTHER 0010000
-#define B57600 0010001
-#define B115200 0010002
-#define B230400 0010003
-#define B460800 0010004
-#define B500000 0010005
-#define B576000 0010006
-#define B921600 0010007
-#define B1000000 0010010
-#define B1152000 0010011
-#define B1500000 0010012
-#define B2000000 0010013
-#define B2500000 0010014
-#define B3000000 0010015
-#define B3500000 0010016
-#define B4000000 0010017
-#define CIBAUD 002003600000 /* input baud rate */
-#define CMSPAR 010000000000 /* mark or space (stick) parity */
-#define CRTSCTS 020000000000 /* flow control */
-
-#define IBSHIFT 16 /* Shift from CBAUD to CIBAUD */
-
-/* c_lflag bits */
-#define ISIG 0000001
-#define ICANON 0000002
-#define XCASE 0000004
-#define ECHO 0000010
-#define ECHOE 0000020
-#define ECHOK 0000040
-#define ECHONL 0000100
-#define NOFLSH 0000200
-#define TOSTOP 0000400
-#define ECHOCTL 0001000
-#define ECHOPRT 0002000
-#define ECHOKE 0004000
-#define FLUSHO 0010000
-#define PENDIN 0040000
-#define IEXTEN 0100000
-#define EXTPROC 0200000
-
-
-/* tcflow() and TCXONC use these */
-#define TCOOFF 0
-#define TCOON 1
-#define TCIOFF 2
-#define TCION 3
-
-/* tcflush() and TCFLSH use these */
-#define TCIFLUSH 0
-#define TCOFLUSH 1
-#define TCIOFLUSH 2
-
-/* tcsetattr uses these */
-#define TCSANOW 0
-#define TCSADRAIN 1
-#define TCSAFLUSH 2
-
-#endif /* __ARCH_M68K_TERMBITS_H__ */
#ifndef _M68K_TERMIOS_H
#define _M68K_TERMIOS_H
-#include <asm/termbits.h>
-#include <asm/ioctls.h>
+#include <uapi/asm/termios.h>
-struct winsize {
- unsigned short ws_row;
- unsigned short ws_col;
- unsigned short ws_xpixel;
- unsigned short ws_ypixel;
-};
-
-#define NCC 8
-struct termio {
- unsigned short c_iflag; /* input mode flags */
- unsigned short c_oflag; /* output mode flags */
- unsigned short c_cflag; /* control mode flags */
- unsigned short c_lflag; /* local mode flags */
- unsigned char c_line; /* line discipline */
- unsigned char c_cc[NCC]; /* control characters */
-};
-
-#ifdef __KERNEL__
/* intr=^C quit=^| erase=del kill=^U
eof=^D vtime=\0 vmin=\1 sxtc=\0
start=^Q stop=^S susp=^Z eol=\0
eol2=\0
*/
#define INIT_C_CC "\003\034\177\025\004\0\1\0\021\023\032\0\022\017\027\026\0"
-#endif
-
-/* modem lines */
-#define TIOCM_LE 0x001
-#define TIOCM_DTR 0x002
-#define TIOCM_RTS 0x004
-#define TIOCM_ST 0x008
-#define TIOCM_SR 0x010
-#define TIOCM_CTS 0x020
-#define TIOCM_CAR 0x040
-#define TIOCM_RNG 0x080
-#define TIOCM_DSR 0x100
-#define TIOCM_CD TIOCM_CAR
-#define TIOCM_RI TIOCM_RNG
-#define TIOCM_OUT1 0x2000
-#define TIOCM_OUT2 0x4000
-#define TIOCM_LOOP 0x8000
-
-/* ioctl (fd, TIOCSERGETLSR, &result) where result may be as below */
-
-#ifdef __KERNEL__
/*
* Translate a "termio" structure into a "termios". Ugh.
#define user_termios_to_kernel_termios_1(k, u) copy_from_user(k, u, sizeof(struct termios))
#define kernel_termios_to_user_termios_1(u, k) copy_to_user(u, k, sizeof(struct termios))
-#endif /* __KERNEL__ */
-
#endif /* _M68K_TERMIOS_H */
#ifndef _ASM_M68K_UNISTD_H_
#define _ASM_M68K_UNISTD_H_
-/*
- * This file contains the system call numbers.
- */
-
-#define __NR_restart_syscall 0
-#define __NR_exit 1
-#define __NR_fork 2
-#define __NR_read 3
-#define __NR_write 4
-#define __NR_open 5
-#define __NR_close 6
-#define __NR_waitpid 7
-#define __NR_creat 8
-#define __NR_link 9
-#define __NR_unlink 10
-#define __NR_execve 11
-#define __NR_chdir 12
-#define __NR_time 13
-#define __NR_mknod 14
-#define __NR_chmod 15
-#define __NR_chown 16
-/*#define __NR_break 17*/
-#define __NR_oldstat 18
-#define __NR_lseek 19
-#define __NR_getpid 20
-#define __NR_mount 21
-#define __NR_umount 22
-#define __NR_setuid 23
-#define __NR_getuid 24
-#define __NR_stime 25
-#define __NR_ptrace 26
-#define __NR_alarm 27
-#define __NR_oldfstat 28
-#define __NR_pause 29
-#define __NR_utime 30
-/*#define __NR_stty 31*/
-/*#define __NR_gtty 32*/
-#define __NR_access 33
-#define __NR_nice 34
-/*#define __NR_ftime 35*/
-#define __NR_sync 36
-#define __NR_kill 37
-#define __NR_rename 38
-#define __NR_mkdir 39
-#define __NR_rmdir 40
-#define __NR_dup 41
-#define __NR_pipe 42
-#define __NR_times 43
-/*#define __NR_prof 44*/
-#define __NR_brk 45
-#define __NR_setgid 46
-#define __NR_getgid 47
-#define __NR_signal 48
-#define __NR_geteuid 49
-#define __NR_getegid 50
-#define __NR_acct 51
-#define __NR_umount2 52
-/*#define __NR_lock 53*/
-#define __NR_ioctl 54
-#define __NR_fcntl 55
-/*#define __NR_mpx 56*/
-#define __NR_setpgid 57
-/*#define __NR_ulimit 58*/
-/*#define __NR_oldolduname 59*/
-#define __NR_umask 60
-#define __NR_chroot 61
-#define __NR_ustat 62
-#define __NR_dup2 63
-#define __NR_getppid 64
-#define __NR_getpgrp 65
-#define __NR_setsid 66
-#define __NR_sigaction 67
-#define __NR_sgetmask 68
-#define __NR_ssetmask 69
-#define __NR_setreuid 70
-#define __NR_setregid 71
-#define __NR_sigsuspend 72
-#define __NR_sigpending 73
-#define __NR_sethostname 74
-#define __NR_setrlimit 75
-#define __NR_getrlimit 76
-#define __NR_getrusage 77
-#define __NR_gettimeofday 78
-#define __NR_settimeofday 79
-#define __NR_getgroups 80
-#define __NR_setgroups 81
-#define __NR_select 82
-#define __NR_symlink 83
-#define __NR_oldlstat 84
-#define __NR_readlink 85
-#define __NR_uselib 86
-#define __NR_swapon 87
-#define __NR_reboot 88
-#define __NR_readdir 89
-#define __NR_mmap 90
-#define __NR_munmap 91
-#define __NR_truncate 92
-#define __NR_ftruncate 93
-#define __NR_fchmod 94
-#define __NR_fchown 95
-#define __NR_getpriority 96
-#define __NR_setpriority 97
-/*#define __NR_profil 98*/
-#define __NR_statfs 99
-#define __NR_fstatfs 100
-/*#define __NR_ioperm 101*/
-#define __NR_socketcall 102
-#define __NR_syslog 103
-#define __NR_setitimer 104
-#define __NR_getitimer 105
-#define __NR_stat 106
-#define __NR_lstat 107
-#define __NR_fstat 108
-/*#define __NR_olduname 109*/
-/*#define __NR_iopl 110*/ /* not supported */
-#define __NR_vhangup 111
-/*#define __NR_idle 112*/ /* Obsolete */
-/*#define __NR_vm86 113*/ /* not supported */
-#define __NR_wait4 114
-#define __NR_swapoff 115
-#define __NR_sysinfo 116
-#define __NR_ipc 117
-#define __NR_fsync 118
-#define __NR_sigreturn 119
-#define __NR_clone 120
-#define __NR_setdomainname 121
-#define __NR_uname 122
-#define __NR_cacheflush 123
-#define __NR_adjtimex 124
-#define __NR_mprotect 125
-#define __NR_sigprocmask 126
-#define __NR_create_module 127
-#define __NR_init_module 128
-#define __NR_delete_module 129
-#define __NR_get_kernel_syms 130
-#define __NR_quotactl 131
-#define __NR_getpgid 132
-#define __NR_fchdir 133
-#define __NR_bdflush 134
-#define __NR_sysfs 135
-#define __NR_personality 136
-/*#define __NR_afs_syscall 137*/ /* Syscall for Andrew File System */
-#define __NR_setfsuid 138
-#define __NR_setfsgid 139
-#define __NR__llseek 140
-#define __NR_getdents 141
-#define __NR__newselect 142
-#define __NR_flock 143
-#define __NR_msync 144
-#define __NR_readv 145
-#define __NR_writev 146
-#define __NR_getsid 147
-#define __NR_fdatasync 148
-#define __NR__sysctl 149
-#define __NR_mlock 150
-#define __NR_munlock 151
-#define __NR_mlockall 152
-#define __NR_munlockall 153
-#define __NR_sched_setparam 154
-#define __NR_sched_getparam 155
-#define __NR_sched_setscheduler 156
-#define __NR_sched_getscheduler 157
-#define __NR_sched_yield 158
-#define __NR_sched_get_priority_max 159
-#define __NR_sched_get_priority_min 160
-#define __NR_sched_rr_get_interval 161
-#define __NR_nanosleep 162
-#define __NR_mremap 163
-#define __NR_setresuid 164
-#define __NR_getresuid 165
-#define __NR_getpagesize 166
-#define __NR_query_module 167
-#define __NR_poll 168
-#define __NR_nfsservctl 169
-#define __NR_setresgid 170
-#define __NR_getresgid 171
-#define __NR_prctl 172
-#define __NR_rt_sigreturn 173
-#define __NR_rt_sigaction 174
-#define __NR_rt_sigprocmask 175
-#define __NR_rt_sigpending 176
-#define __NR_rt_sigtimedwait 177
-#define __NR_rt_sigqueueinfo 178
-#define __NR_rt_sigsuspend 179
-#define __NR_pread64 180
-#define __NR_pwrite64 181
-#define __NR_lchown 182
-#define __NR_getcwd 183
-#define __NR_capget 184
-#define __NR_capset 185
-#define __NR_sigaltstack 186
-#define __NR_sendfile 187
-#define __NR_getpmsg 188 /* some people actually want streams */
-#define __NR_putpmsg 189 /* some people actually want streams */
-#define __NR_vfork 190
-#define __NR_ugetrlimit 191
-#define __NR_mmap2 192
-#define __NR_truncate64 193
-#define __NR_ftruncate64 194
-#define __NR_stat64 195
-#define __NR_lstat64 196
-#define __NR_fstat64 197
-#define __NR_chown32 198
-#define __NR_getuid32 199
-#define __NR_getgid32 200
-#define __NR_geteuid32 201
-#define __NR_getegid32 202
-#define __NR_setreuid32 203
-#define __NR_setregid32 204
-#define __NR_getgroups32 205
-#define __NR_setgroups32 206
-#define __NR_fchown32 207
-#define __NR_setresuid32 208
-#define __NR_getresuid32 209
-#define __NR_setresgid32 210
-#define __NR_getresgid32 211
-#define __NR_lchown32 212
-#define __NR_setuid32 213
-#define __NR_setgid32 214
-#define __NR_setfsuid32 215
-#define __NR_setfsgid32 216
-#define __NR_pivot_root 217
-/* 218*/
-/* 219*/
-#define __NR_getdents64 220
-#define __NR_gettid 221
-#define __NR_tkill 222
-#define __NR_setxattr 223
-#define __NR_lsetxattr 224
-#define __NR_fsetxattr 225
-#define __NR_getxattr 226
-#define __NR_lgetxattr 227
-#define __NR_fgetxattr 228
-#define __NR_listxattr 229
-#define __NR_llistxattr 230
-#define __NR_flistxattr 231
-#define __NR_removexattr 232
-#define __NR_lremovexattr 233
-#define __NR_fremovexattr 234
-#define __NR_futex 235
-#define __NR_sendfile64 236
-#define __NR_mincore 237
-#define __NR_madvise 238
-#define __NR_fcntl64 239
-#define __NR_readahead 240
-#define __NR_io_setup 241
-#define __NR_io_destroy 242
-#define __NR_io_getevents 243
-#define __NR_io_submit 244
-#define __NR_io_cancel 245
-#define __NR_fadvise64 246
-#define __NR_exit_group 247
-#define __NR_lookup_dcookie 248
-#define __NR_epoll_create 249
-#define __NR_epoll_ctl 250
-#define __NR_epoll_wait 251
-#define __NR_remap_file_pages 252
-#define __NR_set_tid_address 253
-#define __NR_timer_create 254
-#define __NR_timer_settime 255
-#define __NR_timer_gettime 256
-#define __NR_timer_getoverrun 257
-#define __NR_timer_delete 258
-#define __NR_clock_settime 259
-#define __NR_clock_gettime 260
-#define __NR_clock_getres 261
-#define __NR_clock_nanosleep 262
-#define __NR_statfs64 263
-#define __NR_fstatfs64 264
-#define __NR_tgkill 265
-#define __NR_utimes 266
-#define __NR_fadvise64_64 267
-#define __NR_mbind 268
-#define __NR_get_mempolicy 269
-#define __NR_set_mempolicy 270
-#define __NR_mq_open 271
-#define __NR_mq_unlink 272
-#define __NR_mq_timedsend 273
-#define __NR_mq_timedreceive 274
-#define __NR_mq_notify 275
-#define __NR_mq_getsetattr 276
-#define __NR_waitid 277
-/*#define __NR_vserver 278*/
-#define __NR_add_key 279
-#define __NR_request_key 280
-#define __NR_keyctl 281
-#define __NR_ioprio_set 282
-#define __NR_ioprio_get 283
-#define __NR_inotify_init 284
-#define __NR_inotify_add_watch 285
-#define __NR_inotify_rm_watch 286
-#define __NR_migrate_pages 287
-#define __NR_openat 288
-#define __NR_mkdirat 289
-#define __NR_mknodat 290
-#define __NR_fchownat 291
-#define __NR_futimesat 292
-#define __NR_fstatat64 293
-#define __NR_unlinkat 294
-#define __NR_renameat 295
-#define __NR_linkat 296
-#define __NR_symlinkat 297
-#define __NR_readlinkat 298
-#define __NR_fchmodat 299
-#define __NR_faccessat 300
-#define __NR_pselect6 301
-#define __NR_ppoll 302
-#define __NR_unshare 303
-#define __NR_set_robust_list 304
-#define __NR_get_robust_list 305
-#define __NR_splice 306
-#define __NR_sync_file_range 307
-#define __NR_tee 308
-#define __NR_vmsplice 309
-#define __NR_move_pages 310
-#define __NR_sched_setaffinity 311
-#define __NR_sched_getaffinity 312
-#define __NR_kexec_load 313
-#define __NR_getcpu 314
-#define __NR_epoll_pwait 315
-#define __NR_utimensat 316
-#define __NR_signalfd 317
-#define __NR_timerfd_create 318
-#define __NR_eventfd 319
-#define __NR_fallocate 320
-#define __NR_timerfd_settime 321
-#define __NR_timerfd_gettime 322
-#define __NR_signalfd4 323
-#define __NR_eventfd2 324
-#define __NR_epoll_create1 325
-#define __NR_dup3 326
-#define __NR_pipe2 327
-#define __NR_inotify_init1 328
-#define __NR_preadv 329
-#define __NR_pwritev 330
-#define __NR_rt_tgsigqueueinfo 331
-#define __NR_perf_event_open 332
-#define __NR_get_thread_area 333
-#define __NR_set_thread_area 334
-#define __NR_atomic_cmpxchg_32 335
-#define __NR_atomic_barrier 336
-#define __NR_fanotify_init 337
-#define __NR_fanotify_mark 338
-#define __NR_prlimit64 339
-#define __NR_name_to_handle_at 340
-#define __NR_open_by_handle_at 341
-#define __NR_clock_adjtime 342
-#define __NR_syncfs 343
-#define __NR_setns 344
-#define __NR_process_vm_readv 345
-#define __NR_process_vm_writev 346
+#include <uapi/asm/unistd.h>
-#ifdef __KERNEL__
-#define NR_syscalls 347
+#define NR_syscalls 348
#define __ARCH_WANT_OLD_READDIR
#define __ARCH_WANT_OLD_STAT
*/
#define cond_syscall(x) asm(".weak\t" #x "\n\t.set\t" #x ",sys_ni_syscall")
-#endif /* __KERNEL__ */
#endif /* _ASM_M68K_UNISTD_H_ */
# UAPI Header export list
include include/uapi/asm-generic/Kbuild.asm
+header-y += a.out.h
+header-y += auxvec.h
+header-y += byteorder.h
+header-y += cachectl.h
+header-y += fcntl.h
+header-y += ioctls.h
+header-y += msgbuf.h
+header-y += param.h
+header-y += poll.h
+header-y += posix_types.h
+header-y += ptrace.h
+header-y += sembuf.h
+header-y += setup.h
+header-y += shmbuf.h
+header-y += sigcontext.h
+header-y += signal.h
+header-y += socket.h
+header-y += sockios.h
+header-y += stat.h
+header-y += swab.h
+header-y += termbits.h
+header-y += termios.h
+header-y += unistd.h
--- /dev/null
+#ifndef __M68K_A_OUT_H__
+#define __M68K_A_OUT_H__
+
+struct exec
+{
+ unsigned long a_info; /* Use macros N_MAGIC, etc for access */
+ unsigned a_text; /* length of text, in bytes */
+ unsigned a_data; /* length of data, in bytes */
+ unsigned a_bss; /* length of uninitialized data area for file, in bytes */
+ unsigned a_syms; /* length of symbol table data in file, in bytes */
+ unsigned a_entry; /* start address */
+ unsigned a_trsize; /* length of relocation info for text, in bytes */
+ unsigned a_drsize; /* length of relocation info for data, in bytes */
+};
+
+#define N_TRSIZE(a) ((a).a_trsize)
+#define N_DRSIZE(a) ((a).a_drsize)
+#define N_SYMSIZE(a) ((a).a_syms)
+
+#endif /* __M68K_A_OUT_H__ */
--- /dev/null
+#ifndef __ASMm68k_AUXVEC_H
+#define __ASMm68k_AUXVEC_H
+
+#endif
--- /dev/null
+#ifndef _M68K_BYTEORDER_H
+#define _M68K_BYTEORDER_H
+
+#include <linux/byteorder/big_endian.h>
+
+#endif /* _M68K_BYTEORDER_H */
projects / ~shefty / rdma-dev.git / commitdiff