~shefty/rdma-dev.git
8 years agommc: tegra: assume CONFIG_OF, remove platform data
Stephen Warren [Fri, 15 Feb 2013 22:07:19 +0000 (15:07 -0700)]
mmc: tegra: assume CONFIG_OF, remove platform data

Tegra only supports, and always enables, device tree. Remove all ifdefs
and runtime checks for DT support from the driver. Platform data is
therefore no longer required. Rework the driver to parse the device tree
directly into struct sdhci_tegra.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
8 years agommc: add DT bindings for more MMC capability flags
Guennadi Liakhovetski [Fri, 15 Feb 2013 15:14:01 +0000 (16:14 +0100)]
mmc: add DT bindings for more MMC capability flags

Many MMC capability flags are platform-dependent and are traditionally set
in platform data. With DT often each such capability requires a special
binding. Add bindings for MMC_CAP_SD_HIGHSPEED, MMC_CAP_MMC_HIGHSPEED,
MMC_CAP_POWER_OFF_CARD and MMC_CAP_SDIO_IRQ capabilities. Also add code to
DT parser to look up "keep-power-in-suspend" and "enable-sdio-wakeup"
bindings and set MMC_PM_KEEP_POWER and MMC_PM_WAKE_SDIO_IRQ respectively,
if found.

Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
8 years agommc: tmio: add support for the VccQ regulator
Guennadi Liakhovetski [Fri, 15 Feb 2013 15:14:00 +0000 (16:14 +0100)]
mmc: tmio: add support for the VccQ regulator

Some SD/MMC interfaces use 2 power regulators: one to power the card itself
(Vcc) and another one to pull signal lines up (VccQ). In case of eMMC and
UHS SD cards the regulators also have to be configured to supply different
voltages. The preferred order of turning supply power on and off is to
turn Vcc first on and last off.

Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
8 years agommc: tmio: remove unused and deprecated symbols
Guennadi Liakhovetski [Fri, 15 Feb 2013 15:13:59 +0000 (16:13 +0100)]
mmc: tmio: remove unused and deprecated symbols

The tmio_mmc_cd_wakeup() inline function has been deprecated since 3.4 and
is unused since 3.4 too. Remove them.

Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
8 years agommc: sh_mobile_sdhi: use managed resource allocations
Guennadi Liakhovetski [Fri, 15 Feb 2013 15:13:58 +0000 (16:13 +0100)]
mmc: sh_mobile_sdhi: use managed resource allocations

Use managed allocations to get memory, clock and interrupts . This
significantly simplifies clean up paths.

Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
8 years agommc: sh_mobile_sdhi: remove unused .pdata field
Guennadi Liakhovetski [Fri, 15 Feb 2013 15:13:57 +0000 (16:13 +0100)]
mmc: sh_mobile_sdhi: remove unused .pdata field

The struct sh_mobile_sdhi_info::pdata field was only used for platform-
based card detection and isn't used anymore since the migration to GPIO-
based MMC slot functions. Remove it.

Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
8 years agommc: tmio-mmc: parse device-tree bindings
Guennadi Liakhovetski [Fri, 15 Feb 2013 15:13:56 +0000 (16:13 +0100)]
mmc: tmio-mmc: parse device-tree bindings

Add parsing of common and driver-specific DT bindings to the tmio-mmc
MMC host driver and the sh_mobile_sdhi interface layer.

Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
8 years agommc: tmio-mmc: define device-tree bindings
Guennadi Liakhovetski [Fri, 15 Feb 2013 15:13:55 +0000 (16:13 +0100)]
mmc: tmio-mmc: define device-tree bindings

Define device-tree bindings for the tmio-mmc driver to be able to specify
parameters, currently provided in platform data.

Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
8 years agommc: sh_mmcif: use mmc_of_parse() to parse standard MMC DT bindings
Guennadi Liakhovetski [Fri, 15 Feb 2013 15:13:54 +0000 (16:13 +0100)]
mmc: sh_mmcif: use mmc_of_parse() to parse standard MMC DT bindings

Use mmc_of_parse() to get interface capability flags and used GPIOs from
device-tree bindings.

Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
8 years agommc: (cosmetic) remove "extern" from function declarations
Guennadi Liakhovetski [Fri, 15 Feb 2013 15:13:53 +0000 (16:13 +0100)]
mmc: (cosmetic) remove "extern" from function declarations

The "extern" keyword isn't required in function declarations, remove it.

Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
8 years agommc: provide a standard MMC device-tree binding parser centrally
Guennadi Liakhovetski [Sat, 16 Feb 2013 15:21:16 +0000 (16:21 +0100)]
mmc: provide a standard MMC device-tree binding parser centrally

MMC defines a number of standard DT bindings. Having each driver parse
them individually adds code redundancy and is error prone. Provide a
standard function to unify the parsing. After all drivers are converted
to using it instead of their own parsers, this function can be integrated
into mmc_alloc_host().

Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
8 years agommc: detailed definition of CD and WP MMC line polarities in DT
Guennadi Liakhovetski [Fri, 15 Feb 2013 15:13:51 +0000 (16:13 +0100)]
mmc: detailed definition of CD and WP MMC line polarities in DT

Clarify ways to specify write-protect and card-detect MMC lines in FDT.

Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
8 years agommc: sdhi, tmio: only check flags in tmio-mmc driver proper
Guennadi Liakhovetski [Fri, 15 Feb 2013 15:13:50 +0000 (16:13 +0100)]
mmc: sdhi, tmio: only check flags in tmio-mmc driver proper

tmio-mmc platform flags can be set by various means, including caller
drivers and device-tree bindings, therefore it is better to only check
them in the tmio-mmc driver proper, not in caller drivers themselves.

Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
8 years agommc: sdhci: Fix parameter of sdhci_do_start_signal_voltage_switch()
Fabio Estevam [Thu, 14 Feb 2013 12:35:03 +0000 (10:35 -0200)]
mmc: sdhci: Fix parameter of sdhci_do_start_signal_voltage_switch()

3714f4315354 ("mmc: sdhci: update signal voltage switch code") changed the
type of the second parameter of sdhci_do_start_signal_voltage_switch(),
from "struct mmc_ios *ios" to "int signal_voltage" which causes the
following build warning:

drivers/mmc/host/sdhci.c:2044:2: warning: initialization from incompatible pointer type [enabled by default]
drivers/mmc/host/sdhci.c:2044:2: warning: (near initialization for 'sdhci_ops.start_signal_voltage_switch') [enabled by default]

Use the previous type so that it matches the start_signal_voltage_switch()
definition from host.h.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: Johan Rudholm <johan.rudholm@stericsson.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
8 years agommc: sdhci: check voltage range only on regulators aware of voltage value
Marek Szyprowski [Tue, 12 Feb 2013 08:01:36 +0000 (09:01 +0100)]
mmc: sdhci: check voltage range only on regulators aware of voltage value

Some regulators don't report any voltage values, so checking supported
voltage range results in disabling all SDHCI_CAN_VDD_* flags and
registration failure. This patch finally provides a correct fix for the
registration of SDHCI driver with all possible voltage regulators:
dummy, fixed and regulated without using regulator_count_voltages()
hacks.

Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
8 years agommc: bcm2835: set SDHCI_QUIRK_DATA_TIMEOUT_USES_SDCLK
Stephen Warren [Sat, 9 Feb 2013 03:56:27 +0000 (20:56 -0700)]
mmc: bcm2835: set SDHCI_QUIRK_DATA_TIMEOUT_USES_SDCLK

SDHCI_QUIRK_DATA_TIMEOUT_USES_SDCLK does basically the same as
implementing struct sdhci_ops .get_timeout_clock, so simply set that
quirk and remove the custom code to simplify the driver.

Reported-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
8 years agommc: support packed write command for eMMC4.5 devices
Seungwon Jeon [Wed, 6 Feb 2013 08:02:46 +0000 (17:02 +0900)]
mmc: support packed write command for eMMC4.5 devices

This patch supports packed write command of eMMC4.5 devices.  Several
writes can be grouped in packed command and all data of the individual
commands can be sent in a single transfer on the bus. Large amounts of
data in one transfer rather than several data of small size are
effective for eMMC write internally.  As a result, packed command help
write throughput be improved.  The following tables show the results
of packed write.

Type A:
test     none |  packed
iozone   25.8 |  31
tiotest  27.6 |  31.2
lmdd     31.2 |  35.4

Type B:
test     none |  packed
iozone   44.1 |  51.1
tiotest  47.9 |  52.5
lmdd     51.6 |  59.2

Type C:
test     none |  packed
iozone   19.5 |  32
tiotest  19.9 |  34.5
lmdd     22.8 |  40.7

Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Reviewed-by: Maya Erez <merez@codeaurora.org>
Reviewed-by: Namjae Jeon <linkinjeon@gmail.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
8 years agommc: add packed command feature of eMMC4.5
Seungwon Jeon [Wed, 6 Feb 2013 08:01:43 +0000 (17:01 +0900)]
mmc: add packed command feature of eMMC4.5

This patch adds packed command feature of eMMC4.5.  The maximum number
for packing read (or write) is offered and exception event relevant to
packed command which is used for error handling is enabled. If host
wants to use this feature, MMC_CAP2_PACKED_CMD should be set.

Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Reviewed-by: Maya Erez <merez@codeaurora.org>
Reviewed-by: Subhash Jadavani <subhashj@codeaurora.org>
Reviewed-by: Namjae Jeon <linkinjeon@gmail.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
8 years agommc: rtsx: remove driving adjustment
Roger Tseng [Mon, 4 Feb 2013 07:45:57 +0000 (15:45 +0800)]
mmc: rtsx: remove driving adjustment

Several new models of readers use different way to select driving
capability (a necessary adjustment along with voltage change). Removing
this from device-independent rtsx_pci_sdmmc module. It will be implemented
in device-depend calls encapsulated by rtsx_pci_switch_output_voltage().

Signed-off-by: Roger Tseng <rogerable@realtek.com>
Reviewed-by: Wei WANG <wei_wang@realsil.com.cn>
Signed-off-by: Chris Ball <cjb@laptop.org>
8 years agommc: use regulator_can_change_voltage() instead of regulator_count_voltages
Marek Szyprowski [Tue, 4 Dec 2012 14:01:02 +0000 (15:01 +0100)]
mmc: use regulator_can_change_voltage() instead of regulator_count_voltages

mmc_regulator_set_ocr() depends on the ability of regulator to change the
voltage value. When regulator cannot change its voltage output, some code
is skipped to avoid reporting false errors on some boards, which use MMC
hosts with fixed regulators (e.g. Samsung Goni and UniversalC210 boards).

This patch replaces a hacky workaround based on regulator_count_voltages()
value with the correct call to recently introduced
regulator_can_change_voltage() function in regulators core.

Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
8 years agommc: sdhci-pxav3: add pm runtime support
Kevin Liu [Fri, 1 Feb 2013 09:48:30 +0000 (17:48 +0800)]
mmc: sdhci-pxav3: add pm runtime support

Signed-off-by: Kevin Liu <kliu5@marvell.com>
Signed-off-by: Jialing Fu <jlfu@marvell.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
8 years agommc: core: fix indentation
Jaehoon Chung [Fri, 1 Feb 2013 05:32:22 +0000 (14:32 +0900)]
mmc: core: fix indentation

This patch fixes incorrect indentation.  (Just code cleanup)

Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
8 years agommc: block: don't start new request when the card is removed
Seungwon Jeon [Tue, 22 Jan 2013 10:48:07 +0000 (19:48 +0900)]
mmc: block: don't start new request when the card is removed

It's not necessary to start a new request while error handling if
the card was removed.

Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Tested-by: Konstantin Dorfman <kdorfman@codeaurora.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
8 years agommc: core: fix permanent sleep of mmcqd during card removal
Seungwon Jeon [Tue, 22 Jan 2013 10:48:03 +0000 (19:48 +0900)]
mmc: core: fix permanent sleep of mmcqd during card removal

This patch is derived from:
"mmc: fix async request mechanism for sequential read scenarios".

According as async transfer, a request is handled with twice mmc_start_req.
When the card is removed, the request is actually not issued in the first
mmc_start_req [__mmc_start_data_req]. And then mmc_wait_for_data_req_done
will come in the next mmc_start_req. But there is no event for completions.
wake_up_interruptible is needed in __mmc_start_data_req for the case of
removed card.

Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Tested-by: Konstantin Dorfman <kdorfman@codeaurora.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
8 years agommc: sdhci: enhance preset value function
Kevin Liu [Thu, 31 Jan 2013 03:31:37 +0000 (11:31 +0800)]
mmc: sdhci: enhance preset value function

4d55c5a1 ("mmc: sdhci: enable preset value after uhs initialization")
added preset value support and enabled it by default during sd card init.

Below are the enhancements introduced by this patch:

1. In current code, preset value is enabled after setting clock finished,
which means the clock is manually set by driver firstly and then suddenly
switched to preset value at this point. So the first setting is useless
and unnecessary. What's more, the first clock setting may differ from the
preset one.  The better way is enable preset value just after switch to
UHS mode so the preset value can take effect immediately. So move preset
value enable from mmc_sd_init_card to sdhci_set_ios which will be called
during set timing.

2. In current code, preset value is disabled at the beginning of
mmc_attach_sd.  It's too late since low freq (400khz) should be set in
mmc_power_up.  So move preset value disable to sdhci_set_ios which will
be called during power up.

3. host->clock and ios->drv_type should also be updated according to the
preset value if it's enabled. Current code missed this.

4. This patch also introduce a quirk to disable preset value in case
preset value doesn't work.

This patch has been verified on sdhci-pxav3 platform with both preset
enabled and disabled.

Signed-off-by: Kevin Liu <kliu5@marvell.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
8 years agommc: mmc_spi: Fix return value evaluation of irq_of_parse_and_map()
Roland Stigge [Wed, 30 Jan 2013 17:05:08 +0000 (18:05 +0100)]
mmc: mmc_spi: Fix return value evaluation of irq_of_parse_and_map()

When irq_of_parse_and_map() returns an error, it does as zero. But in
mmc_spi_get_pdata(), the error return case is compared against NO_IRQ.
This might work where NO_IRQ is zero (defaults to zero when undefined,
as on MIPS) but not where NO_IRQ is different, e.g. on ARM where it's -1.

This patch changes to comparison with 0 which is the error return value
of irq_of_parse_and_map().

Tested on ARM that mmc_spi is working now.

Signed-off-by: Roland Stigge <stigge@antcom.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
8 years agommc: MAINTAINERS update for omap_hsmmc
Balaji T K [Wed, 6 Feb 2013 14:34:43 +0000 (20:04 +0530)]
mmc: MAINTAINERS update for omap_hsmmc

Update Maintainer email for omap_hsmmc, as Venkatraman will no longer
be able to maintain omap_hsmmc driver.

Signed-off-by: Balaji T K <balajitk@ti.com>
Acked-by: Venkatraman S <svenkatr@gmail.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
8 years agommc: sdhci-pltfm: Add a common clk API implementation of get_timeout_clock
Lars-Peter Clausen [Mon, 28 Jan 2013 18:27:12 +0000 (19:27 +0100)]
mmc: sdhci-pltfm: Add a common clk API implementation of get_timeout_clock

Quite a few drivers have a implementation of the get_timeout_clock
callback which simply returns the result of clk_get_rate on the device's
clock. This patch adds a common implementation of this to the sdhci-pltfm
module and replaces all custom implementations with the common one.

Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Tested-by: Stephen Warren <swarren@wwwdotorg.org>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Tested-by: Kevin Liu <kliu5@marvell.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
8 years agommc: sdhci: update signal voltage switch code
Kevin Liu [Mon, 17 Dec 2012 11:29:26 +0000 (19:29 +0800)]
mmc: sdhci: update signal voltage switch code

The protocol related code is moved to core stack. So update the host
driver accordingly.

Signed-off-by: Kevin Liu <kliu5@marvell.com>
Tested-by: Tim Wang <wangtt@marvell.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
8 years agommc: core: Fixup signal voltage switch
Johan Rudholm [Mon, 28 Jan 2013 14:08:28 +0000 (15:08 +0100)]
mmc: core: Fixup signal voltage switch

When switching SD and SDIO cards from 3.3V to 1.8V signal levels, the
clock should be gated for 5 ms during the step. After enabling the
clock, the host should wait for at least 1 ms before checking for
failure. Failure by the card to switch is indicated by dat[0:3] being
pulled low. The host should check for this condition and power-cycle
the card if failure is indicated.

Add a retry mechanism for the SDIO case.

If the voltage switch fails repeatedly, give up and continue the
initialization using the original voltage.

This patch places a couple of requirements on the host driver:

 1) mmc_set_ios with ios.clock = 0 must gate the clock
 2) mmc_power_off must actually cut the power to the card
 3) The card_busy host_ops member must be implemented

if these requirements are not fulfilled, the 1.8V signal voltage switch
will still be attempted but may not be successful.

Signed-off-by: Johan Rudholm <johan.rudholm@stericsson.com>
Signed-off-by: Kevin Liu <kliu5@marvell.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Wei WANG <wei_wang@realsil.com.cn>
Signed-off-by: Chris Ball <cjb@laptop.org>
8 years agommc: core: Break out start_signal_voltage_switch
Johan Rudholm [Mon, 28 Jan 2013 14:08:27 +0000 (15:08 +0100)]
mmc: core: Break out start_signal_voltage_switch

Allow callers to access the start_signal_voltage_switch host_ops
member without going through any cmd11 logic. This is mostly a
preparation for the following signal voltage switch patch.

Also, reset ios.signal_voltage to its original value if
start_signal_voltage_switch fails.

Signed-off-by: Johan Rudholm <johan.rudholm@stericsson.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Wei WANG <wei_wang@realsil.com.cn>
Signed-off-by: Chris Ball <cjb@laptop.org>
8 years agommc: core: Add card_busy to host_ops
Johan Rudholm [Mon, 28 Jan 2013 14:08:26 +0000 (15:08 +0100)]
mmc: core: Add card_busy to host_ops

This host_ops member is used to test if the card is signaling busy by
pulling dat[0:3] low.

Signed-off-by: Johan Rudholm <johan.rudholm@stericsson.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Wei WANG <wei_wang@realsil.com.cn>
Signed-off-by: Chris Ball <cjb@laptop.org>
8 years agommc: core: Add mmc_power_cycle
Johan Rudholm [Mon, 28 Jan 2013 14:08:25 +0000 (15:08 +0100)]
mmc: core: Add mmc_power_cycle

Add mmc_power_cycle which can be used to power cycle for instance
SD-cards.

Signed-off-by: Johan Rudholm <johan.rudholm@stericsson.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Wei WANG <wei_wang@realsil.com.cn>
Signed-off-by: Chris Ball <cjb@laptop.org>
8 years agommc: sd: Simplify by using mmc_host_uhs
Johan Rudholm [Mon, 28 Jan 2013 14:08:24 +0000 (15:08 +0100)]
mmc: sd: Simplify by using mmc_host_uhs

Signed-off-by: Johan Rudholm <johan.rudholm@stericsson.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
8 years agommc: core: expose RPMB partition only for CMD23 capable hosts
Balaji T K [Fri, 25 Jan 2013 11:30:30 +0000 (17:00 +0530)]
mmc: core: expose RPMB partition only for CMD23 capable hosts

SET_BLOCK_COUNT CMD23 is needed for all access to RPMB partition.  If
block count is not set by CMD23, all subsequent read/write commands fail
as per eMMC specification. So, If the host does not support CMD23, do not
expose RPMB partition.

Accessing RPMB partition can cause hang / huge delay for hosts which do
not support CMD23.

Signed-off-by: Balaji T K <balajitk@ti.com>
Reported-and-Tested-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
8 years agommc: goldfish: emulated MMC device
Mike Lockwood [Mon, 21 Jan 2013 23:43:46 +0000 (23:43 +0000)]
mmc: goldfish: emulated MMC device

This driver handles the virtual MMC device present in the Goldfish emulator.
The patch folds together initial work from Mike Lockwood and patches by
San Mehat, Jun Nakajima and Tom Keel <thomas.keel@intel.com> plus cleanups
by Alan Cox to get it all into 3.6 shape.

Signed-off-by: Mike A. Chan <mikechan@google.com>
[cleaned up and x86 support added]
Signed-off-by: Sheng Yang <sheng@linux.intel.com>
Signed-off-by: Yunhong Jiang <yunhong.jiang@intel.com>
Signed-off-by: Xiaohui Xin <xiaohui.xin@intel.com>
Signed-off-by: Jun Nakajima <jun.nakajima@intel.com>
Signed-off-by: Bruce Beare <bruce.j.beare@intel.com>
[Moved to 3.4]
Signed-off-by: Tom Keel <thomas.keel@intel.com>
[Moved to 3.7]
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
8 years agommc: dt: bus-width can be an optional property
Shawn Guo [Mon, 28 Jan 2013 21:49:11 +0000 (16:49 -0500)]
mmc: dt: bus-width can be an optional property

None of mmc drivers implements bus-width as a required device tree
property.  Instead, some drivers like atmel-mci, dw_mmc, sdhci-s3c
implement it as an optional one, and will force bus width to be 1
when the property is absent.  Let's change the common binding to
reflect what the drivers are usually doing.

Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
8 years agommc: sdhci-esdhc-imx: support 8bit mode
Sascha Hauer [Mon, 21 Jan 2013 11:02:28 +0000 (19:02 +0800)]
mmc: sdhci-esdhc-imx: support 8bit mode

The i.MX esdhc has a nonstandard bit layout for the SDHCI_HOST_CONTROL
register. To support 8bit bus width on i.MX populate the platform_bus_width
callback. This is tested on an i.MX25, but should according to the datasheets
work on the other i.MX using this hardware aswell. The i.MX6, while having
a SDHCI_SPEC_300 controller, still uses the same nonstandard register layout.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Tested-by: Dirk Behme <dirk.behme@de.bosch.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
8 years agommc: sdhci: rename platform_8bit_width to platform_bus_width
Sascha Hauer [Mon, 21 Jan 2013 11:02:27 +0000 (19:02 +0800)]
mmc: sdhci: rename platform_8bit_width to platform_bus_width

The 8bit in the function name is misleading. When set, it will be
used to set the bus width, regardless of whether 8bit or another
bus width is requested, so change the function name to
platform_bus_width.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Tested-by: Dirk Behme <dirk.behme@de.bosch.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
8 years agommc: sdhci-esdhc-imx: Auto CMD23 support for usdhc
Shawn Guo [Mon, 21 Jan 2013 11:02:26 +0000 (19:02 +0800)]
mmc: sdhci-esdhc-imx: Auto CMD23 support for usdhc

SDHCI core will try to use Auto CMD23 for mmc card.  Currently, we will
see the following message with mmc card on usdhc due to the lacking of
Auto CMD23 support in the driver.

$ mmc0: new high speed MMC card at address 0001
mmcblk1: mmc0:0001 MMC02G 1.87 GiB
mmcblk1: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb00
mmcblk1: retrying using single block read
 mmcblk1:

Enable Auto CMD23 support for usdhc so that mmc card can work in
multiple block mode.

Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Tested-by: Dirk Behme <dirk.behme@de.bosch.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
8 years agommc: sdhci-esdhc-imx: manually reset MIX_CTRL for usdhc
Shawn Guo [Mon, 21 Jan 2013 11:02:25 +0000 (19:02 +0800)]
mmc: sdhci-esdhc-imx: manually reset MIX_CTRL for usdhc

It's another violation to SDHC spec that software reset on usdhc
does not reset MIX_CTRL register.  Have to do it manually, otherwise
the preserving of the register bits (e.g. AC23EN) may cause mmc card
fail to be initialized.

Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Tested-by: Dirk Behme <dirk.behme@de.bosch.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
8 years agommc: sdhci-esdhc-imx: separate transfer mode from command write for usdhc
Shawn Guo [Mon, 21 Jan 2013 11:02:24 +0000 (19:02 +0800)]
mmc: sdhci-esdhc-imx: separate transfer mode from command write for usdhc

The combining of SDHCI_TRANSFER_MODE and SDHCI_COMMAND writes is only
required for esdhc, but not necessarily for usdhc.  Different from
esdhc where the bits for transfer mode and command are all in the same
register CMD_XFR_TYP, usdhc has a newly introduced register MIX_CTRL
to hold transfer mode bits.  So it makes more sense to separate transfer
mode from command write for usdhc.

Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Tested-by: Dirk Behme <dirk.behme@de.bosch.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
8 years agommc: core: move the cache disabling operation to mmc_suspend
Maya Erez [Mon, 28 Jan 2013 21:44:22 +0000 (16:44 -0500)]
mmc: core: move the cache disabling operation to mmc_suspend

Cache control is an eMMC feature and in therefore should be
part of MMC's bus resume operations, performed in mmc_suspend,
rather than in the generic mmc_suspend_host().

Signed-off-by: Maya Erez <merez@codeaurora.org>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
8 years agoMAINTAINERS: mmc: add maintainer entry for dw_mmc driver
Seungwon Jeon [Thu, 17 Jan 2013 12:33:23 +0000 (21:33 +0900)]
MAINTAINERS: mmc: add maintainer entry for dw_mmc driver

Add maintainer entry for the Synopsys DW host driver which is used in
various SOC including EXYNOS series.  As Will Newton will no longer be
able to take care of dw_mmc*, I and Jaehoon Chung are willing to maintain
it.

Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Will Newton <will.newton@imgtec.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
8 years agommc: sdhci-esdhc-imx: Remove unused variables
Fabio Estevam [Thu, 17 Jan 2013 02:32:52 +0000 (00:32 -0200)]
mmc: sdhci-esdhc-imx: Remove unused variables

3f175a6e5 (mmc: sdhci-esdhc-imx: remove ESDHC_CD_GPIO handling from IO
accessory) introduced the following build warnings:

drivers/mmc/host/sdhci-esdhc-imx.c:149:30: warning: unused variable 'boarddata' [-Wunused-variable]
drivers/mmc/host/sdhci-esdhc-imx.c:181:30: warning: unused variable 'boarddata' [-Wunused-variable]

Remove the unused variables.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
8 years agommc: fix DT binding documentation SDHCI left-over
Guennadi Liakhovetski [Wed, 16 Jan 2013 16:20:41 +0000 (17:20 +0100)]
mmc: fix DT binding documentation SDHCI left-over

The file Documentation/devicetree/bindings/mmc/mmc.txt is common for all
MMC host drivers. Use a generic MMC host reference instead of an SDHCI
left-over.

Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
8 years agommc: sdhci-esdhc-imx: name esdhc specific definitions with ESDHC_ prefix
Shawn Guo [Tue, 15 Jan 2013 15:36:53 +0000 (23:36 +0800)]
mmc: sdhci-esdhc-imx: name esdhc specific definitions with ESDHC_ prefix

Rename esdhc local definitions with ESDHC_ rather than SDHCI_ prefix,
so that we can distinguish them from SDHCI core definitions from name.

A couple of bit fields are also changed use shift for consistency and
better readability.

Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Tested-by: Dirk Behme <dirk.behme@de.bosch.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
8 years agommc: sdhci-esdhc-imx: remove D3CD check from SDHCI_HOST_CONTROL write
Shawn Guo [Tue, 15 Jan 2013 15:36:52 +0000 (23:36 +0800)]
mmc: sdhci-esdhc-imx: remove D3CD check from SDHCI_HOST_CONTROL write

SDHCI_CTRL_D3CD is not a standard SDHCI_HOST_CONTROL, so there is no
need to check it in SDHCI_HOST_CONTROL write at all.  Remove it.

Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Tested-by: Dirk Behme <dirk.behme@de.bosch.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
8 years agommc: sdhci-esdhc-imx: fix host version read
Shawn Guo [Tue, 15 Jan 2013 15:30:27 +0000 (23:30 +0800)]
mmc: sdhci-esdhc-imx: fix host version read

When commit 95a2482 (mmc: sdhci-esdhc-imx: add basic imx6q usdhc
support) works around host version issue on imx6q, it gets the
register address fixup "reg ^= 2" lost for imx25/35/51/53 esdhc.
Thus, the controller version on these SoCs is wrongly identified
as v1 while it's actually v2.

Add the address fixup back and take a different approach to correct
imx6q host version, so that the host version read gets back to work
for all SoCs.

Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
8 years agommc: vt8500: Remove erroneous __exitp in wmt_mci_driver
Tony Prisk [Sun, 13 Jan 2013 06:19:20 +0000 (19:19 +1300)]
mmc: vt8500: Remove erroneous __exitp in wmt_mci_driver

With the __devinit/__devexit attributes having been removed, this
__exitp attribute causes an unused function warning and should be
removed as well.

Signed-off-by: Tony Prisk <linux@prisktech.co.nz>
Signed-off-by: Chris Ball <cjb@laptop.org>
8 years agommc: dw_mmc: Remove DW_MCI_QUIRK_NO_WRITE_PROTECT
Doug Anderson [Fri, 11 Jan 2013 17:03:54 +0000 (17:03 +0000)]
mmc: dw_mmc: Remove DW_MCI_QUIRK_NO_WRITE_PROTECT

The original quirk was added in the change 'mmc: dw_mmc: add quirk to
indicate missing write protect line'.  The original quirk was added at
a controller level even though each slot has its own write protect (so
the quirk should be at the slot level).  A recent change (mmc: dw_mmc:
Add "disable-wp" device tree property) added a slot-level quirk and
support for the quirk directly to dw_mmc.

Signed-off-by: Doug Anderson <dianders@chromium.org>
Acked-by: Will Newton <will.newton@imgtec.com>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Chris Ball <cjb@laptop.org>
8 years agommc: dw_mmc: Handle wp-gpios from device tree
Doug Anderson [Fri, 11 Jan 2013 17:03:53 +0000 (17:03 +0000)]
mmc: dw_mmc: Handle wp-gpios from device tree

On some SoCs (like exynos5250) you need to use an external GPIO for
write protect.  Add support for wp-gpios to the core dw_mmc driver
since it could be useful across multiple SoCs.

With this change I am able to make use of the write protect for the
external SD slot on exynos5250-snow.

Signed-off-by: Doug Anderson <dianders@chromium.org>
Acked-by: Seungwon Jeon <tgih.jun@samsung.com>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Chris Ball <cjb@laptop.org>
8 years agommc: dw_mmc: exynos: Remove code for wp-gpios
Doug Anderson [Fri, 11 Jan 2013 17:03:52 +0000 (17:03 +0000)]
mmc: dw_mmc: exynos: Remove code for wp-gpios

The exynos code claimed the write protect with devm_gpio_request() but
never did anything with it.  That meant that anyone using a write
protect GPIO would effectively be write protected all the time.

The handling for wp-gpios belongs in the main dw_mmc driver and has
been moved there.

Signed-off-by: Doug Anderson <dianders@chromium.org>
Acked-by: Seungwon Jeon <tgih.jun@samsung.com>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Chris Ball <cjb@laptop.org>
8 years agoARM: dts: Add disable-wp for sd card slot on smdk5250
Doug Anderson [Fri, 11 Jan 2013 17:03:51 +0000 (17:03 +0000)]
ARM: dts: Add disable-wp for sd card slot on smdk5250

The next change will remove the code from the dw_mmc-exynos that added
the DW_MCI_QUIRK_NO_WRITE_PROTECT.  Keep existing functionality of
having no write protect pin on smdk5250 by adding the disable-wp
property.

Signed-off-by: Doug Anderson <dianders@chromium.org>
Acked-by: Seungwon Jeon <tgih.jun@samsung.com>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Chris Ball <cjb@laptop.org>
8 years agommc: dw_mmc: Add "disable-wp" device tree property
Doug Anderson [Fri, 11 Jan 2013 17:03:50 +0000 (17:03 +0000)]
mmc: dw_mmc: Add "disable-wp" device tree property

The "disable-wp" property is used to specify that a given SD card slot
doesn't have a concept of write protect.  This eliminates the need for
special case code for SD slots that should never be write protected
(like a micro SD slot or a dev board).

The dw_mmc driver is special in needing to specify "disable-wp"
because the lack of a "wp-gpios" property means to use the special
purpose write protect line.  On some other mmc devices the lack of
"wp-gpios" means that write protect should be disabled.

Signed-off-by: Doug Anderson <dianders@chromium.org>
Acked-by: Seungwon Jeon <tgih.jun@samsung.com>
Acked-by: Will Newton <will.newton@imgtec.com>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Chris Ball <cjb@laptop.org>
8 years agommc: correct the EXCEPTION_EVENTS_STATUS value in comment
Zhang, YiX X [Tue, 8 Jan 2013 06:07:39 +0000 (06:07 +0000)]
mmc: correct the EXCEPTION_EVENTS_STATUS value in comment

The right value is 54 according to eMMC 4.5 specification.

Signed-off-by: ZhangYi <yix.x.zhang@intel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
8 years agommc: mxs-mmc: Fix warning due to incorrect type
Fabio Estevam [Tue, 8 Jan 2013 00:42:35 +0000 (22:42 -0200)]
mmc: mxs-mmc: Fix warning due to incorrect type

Fixes the following warning when building with W=1 option:

drivers/mmc/host/mxs-mmc.c: In function 'mxs_mmc_adtc':
drivers/mmc/host/mxs-mmc.c:401:2: warning: comparison between signed and unsigned integer expressions [-Wsign-compare]

The warning happens because 'i' is used in 'for_each_sg(sgl, sg, sg_len, i)' and should be made unsigned.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Marek Vasut <marex@denx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
8 years agommc: mxs-mmc: Add MODULE_ALIAS()
Fabio Estevam [Mon, 7 Jan 2013 22:41:52 +0000 (20:41 -0200)]
mmc: mxs-mmc: Add MODULE_ALIAS()

Add an entry for MODULE_ALIAS().

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Marek Vasut <marex@denx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
8 years agommc: mvsdio: add pinctrl integration
Thomas Petazzoni [Mon, 28 Jan 2013 11:26:53 +0000 (06:26 -0500)]
mmc: mvsdio: add pinctrl integration

On many Marvell SoCs, the pins used for the SDIO interface are part of
the MPP pins, that are muxable pins. In order to get the muxing of
those pins correct, this commit integrates the mvsdio driver with the
pinctrl infrastructure by calling devm_pinctrl_get_select_default()
during ->probe().

Note that we permit this function to fail because not all Marvell
platforms have yet been fully converted to using the pinctrl
infrastructure.

Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Stefan Peter <s.peter@mpl.ch>
Tested-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Chris Ball <cjb@laptop.org>
8 years agommc: mvsdio: implement a Device Tree binding
Thomas Petazzoni [Wed, 16 Jan 2013 13:13:59 +0000 (14:13 +0100)]
mmc: mvsdio: implement a Device Tree binding

This patch adds a simple Device Tree binding for the mvsdio driver, as
well as the necessary documentation for it. Compatibility with non-DT
platforms is preserved, by keeping the platform_data based
initialization.

We introduce a small difference between non-DT and DT platforms: DT
platforms are required to provide a clocks = <...> property, which the
driver uses to get the frequency of the clock that goes to the SDIO
IP. The behaviour on non-DT platforms is kept unchanged: a clock
reference is not mandatory, but the clock frequency must be passed in
the "clock" field of the mvsdio_platform_data structure.

Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Stefan Peter <s.peter@mpl.ch>
Tested-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Chris Ball <cjb@laptop.org>
8 years agommc: mvsdio: use slot-gpio for card detect gpio
Thomas Petazzoni [Wed, 16 Jan 2013 13:13:58 +0000 (14:13 +0100)]
mmc: mvsdio: use slot-gpio for card detect gpio

The MMC core subsystem provides in drivers/mmc/core/slot-gpio.c a nice
set of helper functions to simplify the management of the card detect
GPIO in MMC host drivers. This patch migrates the mvsdio driver to
using those helpers, which will make the ->probe() code simpler, and
therefore ease the process of adding a Device Tree binding for this
driver.

Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Stefan Peter <s.peter@mpl.ch>
Tested-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Chris Ball <cjb@laptop.org>
8 years agommc: mvsdio: use slot-gpio infrastructure for write protect gpio
Thomas Petazzoni [Wed, 16 Jan 2013 13:13:57 +0000 (14:13 +0100)]
mmc: mvsdio: use slot-gpio infrastructure for write protect gpio

The MMC core subsystem provides in drivers/mmc/core/slot-gpio.c a nice
set of helper functions to simplify the management of the write
protect GPIO in MMC host drivers. This patch migrates the mvsdio
driver to using those helpers, which will make the ->probe() code
simpler, and therefore ease the process of adding a Device Tree
binding for this driver.

Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Stefan Peter <s.peter@mpl.ch>
Tested-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Chris Ball <cjb@laptop.org>
8 years agommc: sdhci-esdhc-imx: remove ESDHC_CD_GPIO handling from IO accessory
Shawn Guo [Tue, 15 Jan 2013 15:19:54 +0000 (23:19 +0800)]
mmc: sdhci-esdhc-imx: remove ESDHC_CD_GPIO handling from IO accessory

With commit 9444e07 (mmc: remove unncessary mmc_gpio_free_cd() call from
slot-gpio users) in place, the ESDHC_CD_GPIO handling in IO accessories
becomes unnecessary.  Remove it.

Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
8 years agommc: sdhci: introduce sdhci_update_clock helper to re-enable clock
Andy Shevchenko [Mon, 7 Jan 2013 14:31:08 +0000 (16:31 +0200)]
mmc: sdhci: introduce sdhci_update_clock helper to re-enable clock

There are three places where same piece of code is used. Let's split it
to a separate function.

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
8 years agommc: sdhci-pxav3: add IRQ wake up support
Kevin Liu [Mon, 14 Jan 2013 19:38:53 +0000 (14:38 -0500)]
mmc: sdhci-pxav3: add IRQ wake up support

[cjb: The MMP3 architecture requires a registered interrupt to retire wfi
when waking from suspend.]

Signed-off-by: Jialing Fu <jlfu@marvell.com>
Signed-off-by: Kevin Liu <kliu5@marvell.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
8 years agommc: sdhci: add IRQ wake up support
Kevin Liu [Sat, 5 Jan 2013 09:21:33 +0000 (17:21 +0800)]
mmc: sdhci: add IRQ wake up support

Don't disable SD Host IRQ during suspend if it is wake up source.
Enable wakeup event during suspend.

Signed-off-by: Jialing Fu <jlfu@marvell.com>
Signed-off-by: Kevin Liu <kliu5@marvell.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
8 years agommc: sdhci: disable interrupt before free_irq
Kevin Liu [Sat, 5 Jan 2013 09:18:28 +0000 (17:18 +0800)]
mmc: sdhci: disable interrupt before free_irq

Current code missed disabling interrupts before free irq which is shared.

Notice below comments for function free_irq (kernel/irq/manage.c):
On a shared IRQ the caller must ensure the interrupt is disabled
on the card it drives before calling this function.

Original code has below issue during suspend/resume when multiple SD
hosts share the same IRQ:
1. Assume there are two hosts (host1 for emmc while host2 for sd) share
the same mmc irq.
2. When system suspend, host2 will be suspended before host1.
So the sequence is below:
step1: irq handler for host2 removed ->
step2: irq handler for host1 removed and irq disabled ->
... system suspended ...
... system resumed ...
step3: irq enabled and the irq handler for host1 restored ->
step4: irq handler for host2 restored
3. So there is the buggy time slot that the irq is enabled but the irq
handler for host2 is removed. Then host2 interrupt can be triggered
but can't be handled at that moment.

Signed-off-by: Jialing Fu <jlfu@marvell.com>
Signed-off-by: Kevin Liu <kliu5@marvell.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
8 years agommc: add BCM2835 driver
Stephen Warren [Thu, 3 Jan 2013 05:34:49 +0000 (22:34 -0700)]
mmc: add BCM2835 driver

Add a very simple driver for the BCM2835 SoC, which is used in the
Raspberry Pi board.

Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
8 years agommc: fix async request mechanism for sequential read scenarios
Konstantin Dorfman [Mon, 14 Jan 2013 19:28:17 +0000 (14:28 -0500)]
mmc: fix async request mechanism for sequential read scenarios

When current request is running on the bus and if next request fetched
by mmcqd is NULL, mmc context (mmcqd thread) gets blocked until the
current request completes. This means that if new request comes in while
the mmcqd thread is blocked, this new request can not be prepared in
parallel to current ongoing request. This may result in delaying the new
request execution and increase it's latency.

This change allows to wake up the MMC thread on new request arrival.
Now once the MMC thread is woken up, a new request can be fetched and
prepared in parallel to the current running request which means this new
request can be started immediately after the current running request
completes.

With this change read throughput is improved by 16%.

Signed-off-by: Konstantin Dorfman <kdorfman@codeaurora.org>
Reviewed-by: Seungwon Jeon <tgih.jun@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
8 years agommc: queue: exclude asynchronous transfer for special request
Seungwon Jeon [Wed, 26 Dec 2012 01:40:17 +0000 (10:40 +0900)]
mmc: queue: exclude asynchronous transfer for special request

Unlike normal r/w request, special requests(discard, flush)
is finished with a one-time issue_fn. Request change to
mqrq_prev makes unnecessary call.

Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Reviewed-by: Konstantin Dorfman <kdorfman@codeaurora.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
8 years agommc: sh_mmcif: simplify IRQ processing
Guennadi Liakhovetski [Wed, 12 Dec 2012 14:45:14 +0000 (15:45 +0100)]
mmc: sh_mmcif: simplify IRQ processing

The classical way to process IRQs is read out the status, ack all triggered
IRQs, possibly mask them, then process them. Follow this simple procesure
instead of the current complex custom algorithm.

Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
8 years agommc: sh_mmcif: report all errors
Teppei Kamijou [Wed, 12 Dec 2012 14:38:18 +0000 (15:38 +0100)]
mmc: sh_mmcif: report all errors

Make error reporting in the driver more verbose. This patch is based on
an earlier work by Teppei Kamijou, but we try to not add any new error
messages to the log in the normal case to avoid confusing the user, and
also add a few more dev_dbg() calls.

Signed-off-by: Teppei Kamijou <teppei.kamijou.yb@renesas.com>
Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi.px@renesas.com>
[g.liakhovetski@gmx.de: avoid producing new errors in normal case]
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
8 years agommc: sh_mmcif: fix I/O errors
Guennadi Liakhovetski [Wed, 12 Dec 2012 14:38:17 +0000 (15:38 +0100)]
mmc: sh_mmcif: fix I/O errors

The INT_BUFWEN IRQ often arrives with other bits set too. If they are not
cleared, an additional IRQ can be triggered, sometimes also after the MMC
request has already been completed. This leads to block I/O errors. Earlier
Teppei Kamijou also observed these additional interrupts and proposed to
explicitly wait for them. This patch chooses an alternative approach of
clearing all active bits immediately, when processing the main interrupt.

Reported-by: Teppei Kamijou <teppei.kamijou.yb@renesas.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
8 years agommc: sh_mmcif: reset DMA completion immediately before starting DMA
Guennadi Liakhovetski [Wed, 12 Dec 2012 14:38:16 +0000 (15:38 +0100)]
mmc: sh_mmcif: reset DMA completion immediately before starting DMA

DMA completion can be signalled from the DMA callback and from the error
handler. If both are called, the completion struct can enter an
inconsistent state. To prevent this move completion initialisation
immediately before activating DMA.

Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
8 years agommc: sh_mmcif: reset error code for any opcode
Guennadi Liakhovetski [Wed, 12 Dec 2012 14:38:15 +0000 (15:38 +0100)]
mmc: sh_mmcif: reset error code for any opcode

If a command execution has produced an error, it has to be reset as a part
of the error handling.

Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
8 years agommc: sh_mmcif: fix a race, causing an Oops on SMP
Guennadi Liakhovetski [Wed, 12 Dec 2012 14:38:14 +0000 (15:38 +0100)]
mmc: sh_mmcif: fix a race, causing an Oops on SMP

Oopses have been observed on SMP in the sh-mmcif IRQ thread, when the two
IRQ threads run simultaneously on two CPUs. Also take care to guard the
timeout work and the DMA completion callback from possible NULL-pointer
dereferences and races.

Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
8 years agommc: sh_mmcif: (cosmetic) simplify boolean return blocks
Guennadi Liakhovetski [Wed, 12 Dec 2012 14:38:13 +0000 (15:38 +0100)]
mmc: sh_mmcif: (cosmetic) simplify boolean return blocks

Use "return condition" instead of "if (condition) return true; return false"
in functions, returning bool.

Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
8 years agommc: sh_mmcif: Terminate DMA transactions when detecting timeout or error
Teppei Kamijou [Wed, 12 Dec 2012 14:38:12 +0000 (15:38 +0100)]
mmc: sh_mmcif: Terminate DMA transactions when detecting timeout or error

If a DMA transaction fails, terminate all outstanding DMA transfers and
unmap buffers.

Signed-off-by: Teppei Kamijou <teppei.kamijou.yb@renesas.com>
Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi.px@renesas.com>
[g.liakhovetski@gmx.de: forward-port, add dma_unmap_sg() in error cases]
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
8 years agommc: sh_mmcif: fix missing and consolidate IO completion timeouts
Guennadi Liakhovetski [Wed, 12 Dec 2012 14:38:11 +0000 (15:38 +0100)]
mmc: sh_mmcif: fix missing and consolidate IO completion timeouts

Read block and write block operations are currently missing completion
timeouts. Add missing timeouts and consolidate them at one location.

Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
8 years agommc: sh_mmcif: Avoid unnecessary mmc_delay() at mmc_card_sleepawake()
Teppei Kamijou [Wed, 12 Dec 2012 14:38:10 +0000 (15:38 +0100)]
mmc: sh_mmcif: Avoid unnecessary mmc_delay() at mmc_card_sleepawake()

SH/R-Mobile MMCIF host controller can wait while the card signals busy.
Set MMC_CAP_WAIT_WHILE_BUSY to inform an upper layer (core/mmc_ops.c)
not to insert unnecessary mmc_delay().

Signed-off-by: Teppei Kamijou <teppei.kamijou.yb@renesas.com>
Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi.px@renesas.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
8 years agommc: sh_mmcif: Use msecs_to_jiffies() for host->timeout
Teppei Kamijou [Wed, 12 Dec 2012 14:38:09 +0000 (15:38 +0100)]
mmc: sh_mmcif: Use msecs_to_jiffies() for host->timeout

Timeout period should be properly normalized using msecs_to_jiffies().

Signed-off-by: Teppei Kamijou <teppei.kamijou.yb@renesas.com>
Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi.px@renesas.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
8 years agommc: sh_mmcif: Add support for eMMC Dual Data Rate
Teppei Kamijou [Wed, 12 Dec 2012 14:38:08 +0000 (15:38 +0100)]
mmc: sh_mmcif: Add support for eMMC Dual Data Rate

Some MMCIF implementations support the Dual Data Rate. With this patch,
platforms can set the MMC_CAP_UHS_DDR50 capability flag in MMCIF platform
data. This will let the MMC core to actually use the DDR mode.

Signed-off-by: Teppei Kamijou <teppei.kamijou.yb@renesas.com>
Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi.px@renesas.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
8 years agommc: sh_mmcif: add support for bundled MMCIF IRQs
Shinya Kuribayashi [Mon, 14 Jan 2013 19:12:36 +0000 (14:12 -0500)]
mmc: sh_mmcif: add support for bundled MMCIF IRQs

On newer SoCs like R-Mobile U2, MMCIF interrupts are bundled.

Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi.px@renesas.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
8 years agommc: sh_mmcif: ensure run-time suspend call is processed before suspend
Teppei Kamijou [Wed, 12 Dec 2012 14:38:06 +0000 (15:38 +0100)]
mmc: sh_mmcif: ensure run-time suspend call is processed before suspend

With this post-v2.6.35 change applied:

commit a0a1a5fd4fb15ec61117c759fe9f5c16c53d9e9c
Author: Tejun Heo <tj@kernel.org>
Date:   Tue Jun 29 10:07:12 2010 +0200
    workqueue: reimplement workqueue freeze using max_active

freeze_workqueues_begin() was introduced and workqueue now gets frozen
before device drivers suspend operations.

We have to ensure that run-time PM suspend operation completes before
system-wide suspend is started.

Signed-off-by: Teppei Kamijou <teppei.kamijou.yb@renesas.com>
Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi.px@renesas.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
8 years agommc: sh_mmcif: force to fail CMD52 immediately
Teppei Kamijou [Wed, 12 Dec 2012 14:38:05 +0000 (15:38 +0100)]
mmc: sh_mmcif: force to fail CMD52 immediately

mmc_rescan() sends CMD52 (SD_IO_RW_DIRECT) to reset SDIO card during
card detection. CMD52 should be ignored by SD/eMMC cards, but we can
also abort it in the driver immediately, since MMCIF doesn't support
SDIO cards anyway.

Signed-off-by: Teppei Kamijou <teppei.kamijou.yb@renesas.com>
Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi.px@renesas.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
8 years agommc: sdhci-esdhc-imx: use slot-gpio helpers for CD and WP
Shawn Guo [Tue, 11 Dec 2012 14:32:20 +0000 (22:32 +0800)]
mmc: sdhci-esdhc-imx: use slot-gpio helpers for CD and WP

Use slot-gpio helpers to save some code in the driver.

Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
8 years agommc: remove unncessary mmc_gpio_free_cd() call from slot-gpio users
Shawn Guo [Tue, 11 Dec 2012 14:32:19 +0000 (22:32 +0800)]
mmc: remove unncessary mmc_gpio_free_cd() call from slot-gpio users

Since slot-gpio uses devm_* managed functions in mmc_gpio_request_cd()
now, we can remove those mmc_gpio_free_cd() call from host drivers'
.probe() error path and .remove().

Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
8 years agommc: slot-gpio: use devm_* managed functions to ease users
Shawn Guo [Tue, 11 Dec 2012 14:32:18 +0000 (22:32 +0800)]
mmc: slot-gpio: use devm_* managed functions to ease users

Use devm_* managed functions, so that slot-gpio users do not have to
call mmc_gpio_free_ro/cd to free up resources requested in
mmc_gpio_request_ro/cd.

Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
8 years agommc: sdhci: query card presence from cd-gpio before asking SDHCI
Shawn Guo [Tue, 11 Dec 2012 07:23:42 +0000 (15:23 +0800)]
mmc: sdhci: query card presence from cd-gpio before asking SDHCI

Call mmc_gpio_get_cd() to query card presence from cd-gpio before
asking SDHCI.  The rationale behind this change is that flag
SDHCI_QUIRK_BROKEN_CARD_DETECTION is designed for SDHCI controller to
tell that SDHCI_PRESENT_STATE is broken, and it should be used for this
case only.  So when cd-gpio is being used, the controller should set
the flag to tell that SDHCI_PRESENT_STATE is not available.

However, the existing code will skip checking cd-gpio as long as flag
SDHCI_QUIRK_BROKEN_CARD_DETECTION is set.  Change the querying order
between cd-gpio and SDHCI to support the rationale above.

Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
8 years agommc: sdio: print correct UHS mode during card detection
Subhash Jadavani [Tue, 4 Dec 2012 11:36:20 +0000 (17:06 +0530)]
mmc: sdio: print correct UHS mode during card detection

When SDIO3.0 card is detected, incorrect bus speed mode
is printed as part of card detection print in kernel logs.

This change fixes it so that user won't be confused by
looking at incorrect card detection message in logs.

Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Tested-by: Jackey Shen <Jackey.Shen@amd.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
8 years agommc: sdio: Fix SDIO 3.0 UHS-I initialization sequence
Sujit Reddy Thumma [Tue, 4 Dec 2012 11:36:19 +0000 (17:06 +0530)]
mmc: sdio: Fix SDIO 3.0 UHS-I initialization sequence

According to UHS-I initialization sequence for SDIO 3.0 cards,
the host must set bit[24] (S18R) of OCR register during OCR
handshake to know whether the SDIO card is capable of doing
1.8V I/O.

Signed-off-by: Sujit Reddy Thumma <sthumma@codeaurora.org>
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Reviewed-by: Johan Rudholm <johan.rudholm@stericsson.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
8 years agommc: sdio: fix resume failure due to lack of CMD52 reset
Subhash Jadavani [Tue, 4 Dec 2012 11:36:18 +0000 (17:06 +0530)]
mmc: sdio: fix resume failure due to lack of CMD52 reset

If SDIO keep power flag (MMC_PM_KEEP_POWER) is not set, card would
be reinitialized during resume but as we are not resetting
(CMD52 reset) the SDIO card during this reinitialization, card may
fail to respond back to subsequent commands (CMD5 etc...).

This change resets the card before the reinitialization of card
during resume.

Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
8 years agodigsig: Fix memory leakage in digsig_verify_rsa()
YOSHIFUJI Hideaki [Fri, 25 Jan 2013 14:54:20 +0000 (16:54 +0200)]
digsig: Fix memory leakage in digsig_verify_rsa()

digsig_verify_rsa() does not free kmalloc'ed buffer returned by
mpi_get_buffer().

Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: Dmitry Kasatkin <dmitry.kasatkin@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: James Morris <james.l.morris@oracle.com>
8 years agoLinux 3.8-rc6
Linus Torvalds [Fri, 1 Feb 2013 01:08:14 +0000 (12:08 +1100)]
Linux 3.8-rc6

8 years agoMerge tag 'dm-3.8-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/agk/linux-dm
Linus Torvalds [Fri, 1 Feb 2013 01:04:22 +0000 (12:04 +1100)]
Merge tag 'dm-3.8-fixes-2' of git://git./linux/kernel/git/agk/linux-dm

Pull more device-mapper fixes from Alasdair G Kergon:
 "A fix for stacked dm thin devices and a fix for the new dm WRITE SAME
  support."

* tag 'dm-3.8-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/agk/linux-dm:
  dm: fix write same requests counting
  dm thin: fix queue limits stacking

8 years agoMerge branch 'for-3.8/upstream-fixes' of git://git.kernel.org/pub/scm/linux/kernel...
Linus Torvalds [Thu, 31 Jan 2013 21:44:59 +0000 (08:44 +1100)]
Merge branch 'for-3.8/upstream-fixes' of git://git./linux/kernel/git/jikos/hid

PullHID fixes from Jiri Kosina:

 - fix i2c-hid and hidraw interaction, by Benjamin Tissoires

 - a quirk to make a particular device (Formosa IR receiver) work
   properly, by Nicholas Santos

* 'for-3.8/upstream-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
  HID: i2c-hid: fix i2c_hid_output_raw_report
  HID: usbhid: quirk for Formosa IR receiver
  HID: remove x bit from sensor doc

8 years agoMerge tag 'nfs-for-3.8-4' of git://git.linux-nfs.org/projects/trondmy/linux-nfs
Linus Torvalds [Thu, 31 Jan 2013 21:43:52 +0000 (08:43 +1100)]
Merge tag 'nfs-for-3.8-4' of git://git.linux-nfs.org/projects/trondmy/linux-nfs

Pull NFS client bugfixes from Trond Myklebust:

 - Error reporting in nfs_xdev_mount incorrectly maps all errors to
   ENOMEM

 - Fix an NFSv4 refcounting issue

 - Fix a mount failure when the server reboots during NFSv4 trunking
   discovery

 - NFSv4.1 mounts may need to run the lease recovery thread.

 - Don't silently fail setattr() requests on mountpoints

 - Fix a SUNRPC socket/transport livelock and priority queue issue

 - We must handle NFS4ERR_DELAY when resetting the NFSv4.1 session.

* tag 'nfs-for-3.8-4' of git://git.linux-nfs.org/projects/trondmy/linux-nfs:
  NFSv4.1: Handle NFS4ERR_DELAY when resetting the NFSv4.1 session
  SUNRPC: When changing the queue priority, ensure that we change the owner
  NFS: Don't silently fail setattr() requests on mountpoints
  NFSv4.1: Ensure that nfs41_walk_client_list() does start lease recovery
  NFSv4: Fix NFSv4 trunking discovery
  NFSv4: Fix NFSv4 reference counting for trunked sessions
  NFS: Fix error reporting in nfs_xdev_mount

8 years agoMerge branch 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus
Linus Torvalds [Thu, 31 Jan 2013 21:43:04 +0000 (08:43 +1100)]
Merge branch 'upstream' of git://git.linux-mips.org/ralf/upstream-linus

Pull MIPS updates from Ralf Baechle:
 "A number of fixes all across the MIPS tree.  No area is particularly
  standing out and things have cooled down quite nicely for a release."

* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
  MIPS: Function tracer: Fix broken function tracing
  mips: Move __virt_addr_valid() to a place for MIPS 64
  MIPS: Netlogic: Fix UP compilation on XLR
  MIPS: AR71xx: Fix AR71XX_PCI_MEM_SIZE
  MIPS: AR724x: Fix AR724X_PCI_MEM_SIZE
  MIPS: Lantiq: Fix cp0_perfcount_irq mapping
  MIPS: DSP: Fix DSP mask for registers.
  MIPS: Fix build failure by adding definition of pfn_pmd().
  MIPS: Octeon: Fix warning.
  MIPS: delay.c: Check BITS_PER_LONG instead of __SIZEOF_LONG__
  MIPS: PNX833x: Fix comment.
  MIPS: Add struct p_format to union mips_instruction.
  MIPS: Export <asm/break.h>.
  MIPS: BCM47xx: Enable SSB prerequisite SSB_DRIVER_PCICORE.
  MIPS: BCM47xx: Select GPIOLIB for BCMA on bcm47xx platform
  MIPS: vpe.c: Fix null pointer dereference in print arguments.

8 years agoHID: i2c-hid: fix i2c_hid_output_raw_report
Benjamin Tissoires [Thu, 31 Jan 2013 16:50:02 +0000 (17:50 +0100)]
HID: i2c-hid: fix i2c_hid_output_raw_report

i2c_hid_output_raw_report is used by hidraw to forward set_report requests.
The current implementation of i2c_hid_set_report needs to take the
report_id as an argument. The report_id is stored in the first byte
of the buffer in argument of i2c_hid_output_raw_report.

Not removing the report_id from the given buffer adds this byte 2 times
in the command, leading to a non working command.

Reported-by: Andrew Duggan <aduggan@synaptics.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
8 years agoMIPS: Function tracer: Fix broken function tracing
Al Cooper [Wed, 16 Jan 2013 22:43:28 +0000 (22:43 +0000)]
MIPS: Function tracer: Fix broken function tracing

Function tracing is currently broken for all 32 bit MIPS platforms.
When tracing is enabled, the kernel immediately hangs on boot.
This is a result of commit b732d439cb43336cd6d7e804ecb2c81193ef63b0
that changes the kernel/trace/Kconfig file so that is no longer
forces FRAME_POINTER when FUNCTION_TRACING is enabled.

MIPS frame pointers are generally considered to be useless because
they cannot be used to unwind the stack. Unfortunately the MIPS
function tracing code has bugs that are masked by the use of frame
pointers. This commit fixes the bugs so that MIPS frame pointers
don't need to be enabled.

The bugs are a result of the odd calling sequence used to call the trace
routine. This calling sequence is inserted into every traceable function
when the tracing CONFIG option is enabled. This sequence is generated
for 32bit MIPS platforms by the compiler via the "-pg" flag.

Part of the sequence is "addiu sp,sp,-8" in the delay slot after every
call to the trace routine "_mcount" (some legacy thing where 2 arguments
used to be pushed on the stack). The _mcount routine is expected to
adjust the sp by +8 before returning.  So when not disabled, the original
jalr and addiu will be there, so _mcount has to adjust sp.

The problem is that when tracing is disabled for a function, the
"jalr _mcount" instruction is replaced with a nop, but the
"addiu sp,sp,-8" is still executed and the stack pointer is left
trashed. When frame pointers are enabled the problem is masked
because any access to the stack is done through the frame
pointer and the stack pointer is restored from the frame pointer when
the function returns.

This patch writes two nops starting at the address of the "jalr _mcount"
instruction whenever tracing is disabled. This means that the
"addiu sp,sp.-8" will be converted to a nop along with the "jalr".  When
disabled, there will be two nops.

This is SMP safe because the first time this happens is during
ftrace_init() which is before any other processor has been started.
Subsequent calls to enable/disable tracing when other CPUs ARE running
will still be safe because the enable will only change the first nop
to a "jalr" and the disable, while writing 2 nops, will only be changing
the "jalr". This patch also stops using stop_machine() to call the
tracer enable/disable routines and calls them directly because the
routines are SMP safe.

When the kernel first boots we have to be able to handle the gcc
generated jalr, addui sequence until ftrace_init gets a chance to run
and change the sequence. At this point mcount just adjusts the stack
and returns. When ftrace_init runs, we convert the jalr/addui to nops.
Then whenever tracing is enabled we convert the first nop to a "jalr
mcount+8". The mcount+8 entry point skips the stack adjust.

[ralf@linux-mips.org: Folded in  Steven Rostedt's build fix.]

Signed-off-by: Al Cooper <alcooperx@gmail.com>
Cc: rostedt@goodmis.org
Cc: ddaney.cavm@gmail.com
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/4806/
Patchwork: https://patchwork.linux-mips.org/patch/4841/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>